Bedienungsanleitung Olympia CM 1856 F (Seite 69 von 70) (Englisch)

569206

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Page 69

OLYMPIA CM 1856F _______________________Programming Instruction___________________________________

Activate SPRINTER wireless module

Connection to the power supply

Before you connect the SPRINTER system to the power supply, the cash register and the printer should

both be turned on. Plug the adapter into the powersocket. Then connect the adapter with the power

supply connection on the module.

A self-test starts automatically. The green LED and the red LED blink once. If no errors are

found, the green LED lights up and the other LEDs are off. The system is now ready for use! If

an error occurs, all LEDs blink on and off and you hear a long beeping sound. Disconnect the

module from the electricity supply and then reconnect it with the electricity supply. If the error

is still present, contact a specialized dealer, if the error is no longer present, you can carry on

with the registration process.

Registering the POS module

In order to guarantee the correct operation, all POS modules have to be registered with every KP module

before they can be used. Every POS module has its own and unalterable ID, which is appointed at the

factory. This ID must be registered at the KP modules, as here described. All POS modules should be

registered singly and one after the other.

Before beginning the registration, all POS and KP modules should be ready for use (e.g. not in the

process of printing).

i) Set all third DIP switches on all KP modules to “ON” in order to get into the register mode. All

LEDs on the KP module blink on and off and you hear 2 beeping sounds. At the same time the

printer ID and the current registration list is printed out on the printer.

ii) Hold down the button “LEARN” on the POS module until you hear 2

beeping sounds.

iii) After releasing the button, the POS module is in registration mode. All

LEDs blink on and off.

iv) The ID of the POS module is sent automatically to all KP modules. If the registration with a KP

module was successful, then the corresponding LED lights up. When the registration process is

finished (after approx. 10 seconds), you hear 2 beeping sounds.

v) If the registration does not complete successfully, repeat the steps described.

vi) To return to the registration mode, press the “LEARN” button again.

The green LED lights up and all the red LEDs are out.

vii) Repeat the steps (iii) to (vi) for each module to register further POS Modules with the KP module.

viii) When all the POS modules have been registered with the KP module, set the third DIP switch on

the KP module back to the “OFF“ position in order to return to operation mode. As a control, the

printer ID and the updated registration lists are printed out on the printer.

Detailed settings are described in the instructions for the SPRINTER module.

LEARN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olympia CM 1856 F Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Olympia CM 1856 F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info