Bedienungsanleitung Onkyo PR-SC886 (Seite 130 von 134) (Englisch)

61148

130

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

130

Troubleshooting—Continued

Can’t record

• On your recorder, make sure the correct input is

selected.

• To prevent signal loops and damage to the AV control-

ler, input signals are not fed through to outputs with

the same name (e.g., TAPE IN to TAPE OUT or

VCR/DVR IN to VCR/DVR OUT).

• When the Pure Audio listening mode is selected,

video recording is not possible because no video sig-

nals are output. Select another listening mode.

There’s no sound

• Only components connected to analog inputs can be

played in Zone 2 and Zone 3.

The sound changes when I connect my head-

phones

• When a pair of headphones is connected, the listening

mode is set to Stereo, unless it’s already set to Stereo,

Mono, Direct, or Pure Audio.

The speaker volume cannot be set as required

• When the Automatic Speaker Setup function is used,

or the volume is adjusted on the onscreen setup

menus, the maximum possible volume setting may

change.

The speaker distance cannot be set as required

• In some cases, corrected values suitable for home the-

ater use may be set automatically.

The display doesn’t work

• The display is turned off when the Pure Audio listen-

ing mode is selected.

How do I change the language of a multiplex

source

• On the “Audio Adjust” menu, change the “Multiplex”

setting to “Main” or “Sub” (page 98).

The u functions don’t work

• To use u, you must make an u connection and an

analog audio connection (RCA) between the compo-

nent and AV controller, even if they are connected dig-

itally (page 44).

• While Zone 2 or Zone 3 is selected, the u functions

don’t work.

The functions Auto Power On/Standby and

Direct Change don’t work for components con-

nected via u

• These functions don’t work when Zone 2 is turned on.

When performing “Automatic Speaker Setup”,

the measurement fails showing the message

“Ambient noise is too high”.

• This can be caused by any malfunction in your speaker

unit. Check if the unit produces normal sounds.

Recording

Zone 2/Zone 3

Others

The AV controller contains a microcomputer for signal

processing and control functions. In very rare situations,

severe interference, noise from an external source, or

static electricity may cause it to lockup. In the unlikely

event that this happens, unplug the power cord from the

wall outlet, wait at least 5 seconds, and then plug it back

in again.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

this unit’s malfunction. Before you record important

data, make sure that the material will be recorded cor-

rectly.

For North American model, set the AV controller to

Standby before disconnecting the power cord from the

wall outlet. For other models, set the AV controller to

Standby and the POWER switch to OFF before discon-

necting the power cord.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo PR-SC886 Seite 130

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info