Bedienungsanleitung Onkyo SKB-940 (Seite 62 von 68) (Englisch)

601412

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Troubleshooting

—Continued

Reception is noisy, stereo FM reception suffers

from hiss, or the FM STEREO indicator doesn’t

appear

• Relocate your antenna.

•Move the AV receiver away from your TV or com-

puter.

• Listen to the station in mono (page 39).

• When listening to an AM station, operating the remote

controller may cause noise.

•Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor

antenna.

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 13).

• Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the AV

receiver’s remote control sensor (page 13).

• Make sure you’ve selected the correct remote control-

ler mode (page 14).

• Make sure you’ve entered the correct remote control

code (page 57).

Can’t control other components

• Make sure you’ve selected the correct remote control-

ler mode (page 14).

• If you’ve connected an -capable Onkyo MD

recorder, CD recorder, or next generation HDD-com-

patible component to the TAPE IN/OUT jacks, or a

DS-A1 Remote Interactive Dock to the VIDEO 2 IN

jacks, for the remote controller to work properly, you

must set the Input Display to MD, CDR, or HDD (see

page 35).

• The entered remote control code may not be correct. If

more than one code is listed, try each one.

•With some AV components, certain buttons may not

work as expected, and some may not work at all.

•To control an Onkyo component that’s connected via

, point the remote controller at the AV receiver. Be

sure to enter the appropriate remote control code ﬁrst

(see page 58).

•To control an Onkyo component that’s not connected

via , or another manufacturer’s component, point

the remote controller at the component. Be sure to

enter the appropriate remote control code ﬁrst (see

page 57).

Can’t record

• On your recorder, make sure the correct input is

selected.

•To prevent signal loops and damage to the AV

receiver, input signals are not fed through to outputs

with the same name (e.g., TAPE IN to TAPE OUT, or

VIDEO 1 IN to VIDEO 1 OUT).

• When the Pure Audio listening mode (not North

American model) is selected, recording is not possible

because no video signals are output. Select another lis-

tening mode.

The sound changes when I connect my head-

phones

• When a pair of headphones is connected, the listening

mode is set to Stereo, unless it’s already set to Stereo,

Mono, Direct, or Pure Audio (not North American

model).

The display doesn’t work

• The display is turned off when the Pure Audio listen-

ing mode (not North American model) is selected.

How do I change the language of a multiplex

source

• Use the “Multiplex” setting on the “Audio Adjust”

menu to select Main or Sub (page 50).

The functions don’t work

•To use , you must make an connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver, even if they are connected digi-

tally (page 33).

Tuner

Remote Controller

Recording

Others

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo SKB-940 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info