517113
70
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
70
FM/AM TUNER
AM stations cannot be received.
AM loop antenna is not connected.
Connect the included AM loop antenna to the AM antenna
terminals.
Buzzing noise on AM stations (particularly noticeable at
night or with weak stations).
Noise from electrical apparatus such as fluorescent lamp.
Move the AM loop antenna to different position.
Set up an outdoor AM antenna.
Noise is heard at high-pitched sounds on AM stations.
Noise from TV set.
Place the AM loop antenna as far as possible from the TV.
Move unit away from TV set.
Crackling noise on both AM and FM stations.
Noise caused by fluorescent lamp being turned on and off.
Move antenna as far as possible from the fluorescent lamp.
Noise from automobile ignition.
Install an FM outdoor antenna as far as possible from the
road.
Change the position or direction of the outdoor antenna.
The indicators light for stereo reception, but sound is
distorted and stereo separation is bad.
Station is too strong.
Change to FM indoor antenna.
Multiple reflection of the radio waves because of tall buildings
or mountains.
Use antenna that has better directivity and select a point
where distortion is least.
Indicators for stereo reception flicker and hiss is heard
on FM stations.
Station is too weak.
Install an outdoor FM antenna.
Stereo FM broadcasts cover only about half the distance of an
ordinary broadcast.
Change the position or direction of the outdoor antenna.
No preset station is recalled.
Power cord has been unplugged or the POWER switch has been
turned off for a long time.
The memory contents are lost. Store all stations again.
Troubleshooting guide
If a problem occurs while you are using the remote controller, first
try to operate the controls on the front panel of the TX-DS898 to
make sure that it is not due to a malfunction (or worn out batteries) in
the remote controller.
POWER
Power shuts off immediately after power on.
Amplifier protection circuitry has been activated.
Remove the power cord from outlet immediately. Contact
your Onkyo service center.
No power.
Power cord is disconnected.
Connect power cord.
External noise in the affecting the internal microcomputer.
Turn the power button off and then on again or remove the
power cord from the outlet and then plug it in again.
Internal fuse is blown.
Contact your Onkyo Service Center.
Power turns on but no sound.
•“Muting is displayed.
Press the MUTING button on the remote controller to turn it
off.
Bad connections or wiring.
Check connections, speaker cables, etc.
Amplifier protection circuitry has been activated.
Contact your Onkyo Service Center.
The sound of the playback source is not heard.
Input selector is not set properly.
Set to correct input source.
Headphones are connected.
Lower volume and then disconnect headphones.
SPEAKERS
No sound from the center speaker, or at very low
volume.
Speaker cable is not connected.
Check the connection between the amplifier and the speaker.
Listening mode is set to Stereo or Direct.
Set the Listening mode to any mode other than Stereo or
Direct. The output to the center speaker may differ depending
on the listening mode.
Center speaker level is set to minimum.
Set the Center speaker level to the appropriate volume (page
31).
The Center setting of the Speaker Config submenu is set to
None.
Set the Center setting at the Speaker Config submenu to
Large or Small (see page 29).
No sound or very low volume from subwoofer.
Subwoofer is set to No.
Check the speaker setting (pages 29, 40).
Subwoofer speakers output level setting is improper.
Check the output level of the Subwoofer using the test tone.
Low frequency humming is heard.
Not properly grounded.
Check outer conductor of input plugs.
Turntable motor is not properly grounded.
Check for proper ground connection.
Audio connection cables on the rear panel are connected
incorrectly.
Adjust the placement of the cable to reduce hum.
Howling is heard when the volume is turned up.
Turntable and speakers are located too close together.
Move them farther apart.
Rough or scratchy sound is heard. High range is not
clear.
The needles of turntable is dirty or worn, or a problem exists
with a connected component.
Refer to the instruction of the connected components and
check for problem.
Treble control is too high.
Turn treble down (see page 40).
70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Onkyo TX-DS898 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info