Bedienungsanleitung Onkyo TX-DS989 (Seite 3 von 76) (Englisch)

553759

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

1. Warranty Claim

You can find the serial number on the rear panel of this unit. In

case of warranty claim, please report this number.

2. Recording Copyright

Recording of copyrighted material for other than personal use is

illegal without permission of the copyright holder.

3. AC Fuse

The fuse is located inside the chassis and is not user-serviceable. If

power does not come on, contact your Onkyo authorized service station.

4. Care

From time to time you should wipe the front and rear panels and

the cabinet with a soft cloth. For heavier dirt, dampen a soft cloth

in a weak solution of mild detergent and water, wring it out dry,

and wipe off the dirt. Following this, dry immediately with a clean

cloth. Do not use rough material, thinners, alcohol or other chemi-

cal solvents or cloths since these could damage the finish or re-

move the panel lettering.

5. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,

READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to

country or region. Be sure that the power supply voltage of the

area where this unit will be used meets the required voltage (e.g.,

AC 230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.

Precautions

For U.S. model

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s at-

tention to Article 820-40 of the NEC, ANSI/NFPA 70, which pro-

vides guidelines for proper grounding and, in particular, specifies

that the cable ground shall be connected to the grounding system

of the building, as close to the point of cable entry as practical.

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to

operate the equipment.

NOTE:

This equipment has been tested and found to comply with the lim-

its for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. How-

ever, there is no guarantee that interference will not occur in a par-

ticular installation. If this equipment does cause harmful interfer-

ence to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

For Canadian model

CAUTION: THIS DIGITAL APPARATUS DOES NOT EX-

CEED THE CLASS B LIMITS FOR RADIO NOISE EMISSION

FROM DIGITAL APPARATUS SET OUT IN THE RADIO IN-

TERFERENCE REGULATIONS OF THE CANADIAN DE-

PARTMENT OF COMMUNICATIONS.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modele pour les Canadien

ATTENTION:L'INTERFÉRENCE RADIO ÉLECTRIQUE

GÉNÉRÉE PAR CET APPAREIL NUMÉRIQUE DE TYPE B

NE DÉPASSE PAS LES LIMITES ÉNONCÉES DANS LE

RÈGLEMENT SUR LES PERTURBATIONS RADIO

ÉLECTRIQUES, SECTION APPAREIL NUMÉRIQUE, DU

MINISTÈRE DES COMMUNICATIONS.

Sur les modèles dont la fiche est polarisée:

ATTENTION:POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE

DANS LA BORNE CORRESPONDANTE DE LA PRISE ET

POUSSER JUSQU’AU FOND.

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

S2898A

21. Replacement Parts–When replacement parts are required, be

sure the service technician has used replacement parts speci-

fied by the manufacturer or have the same characteristics as

the original part. Unauthorized substitutions may result in fire,

electric shock, or other hazards.

22. Safety Check – Upon completion of any service or repairs to the

appliance, ask the service technician to perform safety checks to

determine that the appliance is in proper operation condition.

23. Wall or Ceiling Mounting – The appliance should be mounted

to a wall or ceiling only as recommended by the manufacturer.

24. Heat – The appliance should be situated away from heat

sources such as radiators, heat registers, stoves, or other appli-

ances (including amplifiers) that produce heat.

FIGURE 1:

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL

ELECTRICAL CODE, ANSI/NFPA 70

Taped

Precautions during unpacking

• The unit is extremely heavy, so be careful when lifting it so

as not to cause an injury. Do not lift or move the unit by hold-

ing it at the door on the front panel. Doing so may damage the

front door.

• When packaged, the door on the front panel is taped to the

unit. Before use, be sure to remove this tape.

OFF

STANDBY/ON

STANDBY

MASTER VOLUME

POWER

DISPLAY DVD

VIDEO

TAPE

PHONO

C D

OPEN/CLOSE

ZONE

()

GRN

REC

()

RED

RECEIVER

TX-DS989

• The taping for packaging may be different for your product.

Onkyo TX-DS989 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info