Bedienungsanleitung Onkyo TX-SR252 (Seite 31 von 35) (Englisch)

645302

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Additional information

HDMI

 No picture or sound.

 If the problem still persists when connecting your HDMI

component directly to your monitor, please consult the

component or monitor manual or contact the manufacturer for

support.

 No picture.

 Video signals that are input from the analog video terminal will

not output from the HDMI terminal. Signals that are input from

the HDMI terminal will not output from the analog video

terminal. Be consistent with the type of cable between input

and output.

 Depending in the output settings of the source component, it

may be outputting a video format that can’t be displayed.

Change the output settings of the source, or connect using the

composite video jacks.

 This receiver is HDCP-compatible. Check that the components

you are connecting are also HDCP-compatible. If they are not,

please connect them using the composite video jacks.

 Depending on the connected source component, it’s possible

that it will not work with this receiver (even if it is HDCP-

compatible). In this case, connect using the composite video

jacks between source and receiver.

 If video images do not appear on your TV, try adjusting the

resolution, Deep Color or other setting for your component.

 To output signals in Deep Color, use an HDMI cable (High

Speed HDMI

®/

™ Cable) to connect this receiver to a

component or TV with the Deep Color feature.

 The OSD screen (Home Menu, etc.) isn’t displayed.

 The OSD will not appear if you have connected using the

composite output to your TV. Use HDMI connections when

setting up the system.

 No sound, or sound suddenly ceases.

 Check that the HDMI setting is set to AMP (page 24).

 If the component is a DVI device, use a separate connection for

the audio.

 HDMI format digital audio transmissions require a longer time

to be recognized. Due to this, interruption in the audio may

occur when switching between audio formats or beginning

playback.

 Turning on/off the device connected to this unit’s HDMI OUT

terminal during playback, or disconnecting/connecting the

HDMI cable during playback, may cause noise or interrupted

audio.

Important information regarding the HDMI

connection

There are cases where you may not be able to route HDMI

signals through this receiver (this depends on the HDMI

equipped component you are connecting-check with the

manufacturer for HDMI compatibility information).

If you aren’t receiving HDMI signals properly through this

receiver (from your component), please try the following

configuration when connecting up.

Configuration

Connect your HDMI-equipped component directly to the

display using an HDMI cable. Then use the most convenient

connection (digital is recommended) for sending audio to the

receiver. See the operating instructions for more on audio

connections. Set the display volume to minimum when using

this configuration.

Note

•

Depending on the component, audio output may be limited

to the number of channels available from the connected

display unit (for example audio output is reduced to 2

channels for a monitor with stereo audio limitations).

•

If you want to switch the input source, you’ll have to switch

functions on both the receiver and your display unit.

•

Since the sound is muted on the display when using the

HDMI connection, you must adjust the volume on the

display every time you switch input sources.

USB messages

 ‘USB Error 1 (I/U ERR1)’

 There is a problem with the signal path from the USB to the

receiver. Switch off the receiver and reconnect the USB to the

receiver.

 ‘USB Error 3 (I/U ERR3)’

 When there is no response from the USB. Switch off the

receiver and reconnect the USB to the receiver.

 ‘USB Error 4 (I/U ERR4)’

 The power requirements of the USB device are too high for this

receiver. Switch off the receiver and reconnect the USB to the

receiver.

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the

factory default. Use the front panel controls to do this.

Switch the receiver into standby.

While holding down

DIRECT

, press and hold



ON/

STANDBY

for about two seconds.

When you see RESET? appear in the display, press

STEREO

OK? shows in the display.

Press

SURROUND

to confirm.

OK appears in the display to indicate that the receiver

has been reset to the factory default settings.

Important

•

If the Standby Through is not set to OFF, you may not be

able to initialize the unit.

Cleaning the unit

•

Use a polishing cloth or dry cloth to wipe off dust and dirt.

•

When the surface is dirty, wipe with a soft cloth dipped in

some neutral cleanser diluted five or six times with water,

and wrung out well, and then wipe again with a dry cloth.

Do not use furniture wax or cleansers.

•

Never use thinners, benzine, insecticide sprays or other

chemicals on or near this unit, since these will corrode the

surface.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR252 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR252

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info