Bedienungsanleitung Onkyo TX-SR404 (Seite 56 von 60) (Englisch)

645315

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Troubleshooting

—Continued

• On the AV receiver, the subwoofer setting in the

speaker conﬁguration is set to No. Set the subwoofer

setting to Yes.

There’s no sound with a certain signal format?

• Check the digital audio output setting on the con-

nected device. On some games consoles, such as those

that can play DVDs, the default setting is off.

•With some DVD-Video discs, you need to select an

audio output format from a menu.

Can’t get 5.1-channel playback?

• When speaker B is turned on, speaker set A is reduced

to 2.1-channel playback.

The volume cannot be set to 79?

• When the subwoofer volume level is set to a positive

(+) value, the maximum master volume level is

reduced proportionally.

Noise can be heard?

• Using cable ties to bundle audio cables with power

cords, speaker cables, and so on may degrade the

audio performance, so don’t do it.

• An audio cable may be picking up interference. Try

repositioning your cables.

The Late Night function doesn’t work?

• Make sure the source material is Dolby Digital

(page 49).

The DVD analog multichannel input doesn’t

work?

• Check the DVD analog multichannel input connec-

tions (page 25).

•To select the DVD analog multichannel input, press

the [MULTI CH] input selector button (page 37).

• Check the audio output settings on your DVD player.

About DTS signals

• When DTS program material ends and the DTS bit-

stream stops, the AV receiver remains in DTS listening

mode and the DTS indicator remains on. This is to pre-

vent noise when you use the pause, fast forward, or fast

reverse function on your player. If you switch your

player from DTS to PCM, because the AV receiver

does not switch formats immediately, you may not hear

any sound, in which case you should stop your player

for about three seconds, and then resume playback.

•With some CD players, you won’t be able to playback

DTS material properly even though your player is con-

nected to a digital input on the AV receiver. This is

usually because the DTS bitstream has been processed

(e.g., output level, sampling rate, or frequency

response changed) and the AV receiver doesn’t recog-

nize it as a genuine DTS signal. In such cases, you

may hear noise.

• When playing DTS program material, using the pause,

fast forward, or fast reverse function on your player

may produce a short audible noise. This is not a mal-

function.

There’s no picture?

• Make sure that all video connecting plugs are pushed

in all the way (page 22).

• Make sure that each video component is properly con-

nected.

• The AV receiver does not convert between formats, so

if a video source component is connected to a compo-

nent video input, your TV must be connected to the

component video output (page 23).

• On your TV, make sure that the video input to which

the AV receiver is connected is selected.

Reception is noisy, stereo FM reception suffers

from hiss, or the FM STEREO indicator doesn’t

appear?

• Relocate your antenna.

•Move the AV receiver away from your TV or com-

puter.

• Listen to the station in mono (page 38).

• When listening to an AM station, operating the remote

controller may cause noise.

•Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor

antenna (page 21).

The remote controller doesn’t work?

• Make sure that the batteries are installed with the cor-

rect polarity (page 9).

• Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the AV

receiver’s remote control sensor (page 9).

• Make sure you’ve selected the correct remote control-

ler mode (page 10).

• Make sure you’ve entered the correct remote control

code.

Can’t control other components?

• Make sure you’ve selected the correct remote control-

ler mode (page 10).

• If you’ve connected an -capable Onkyo MD

recorder, CD recorder, or next generation HDD-com-

patible component to the TAPE IN/OUT jacks, or a

DS-A1 Remote Interactive Dock to the VIDEO 3 IN

jacks, for the remote controller to work properly, you

must set the Input Display to MD, CDR, or HDD (see

page 33).

•To control an Onkyo component that’s connected via

, point the remote controller at the AV receiver.

Video

Tuner

Remote Controller

TX-SR304_En.book Page 56 Tuesday, February 7, 2006 4:57 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR404 Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info