Bedienungsanleitung Onkyo TX-SR603E (Seite 91 von 92) (Englisch)

645323

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Troubleshooting

—Continued

Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t

appear?

• Relocate your antenna.

• Move the AV receiver away from your TV or com-

puter.

• Listen to the station in mono (page 56).

• When listening to an AM station, operating the remote

controller may cause noise.

• Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor

antenna.

The remote controller doesn’t work?

• Make sure that the batteries are installed with the cor-

rect polarity (page 13).

• Install new batteries. Don’t mix different types of bat-

teries, or old and new batteries (page 13).

• Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the AV

receiver’s remote control sensor (page 13).

• Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type ﬂuorescent lights.

Relocate if necessary.

• If the AV receiver is installed in a rack or cabinet with

colored-glass doors, the remote controller may not

work reliably when the doors are closed.

• Make sure you’ve selected the correct remote control-

ler mode (pages 14-19).

• When using the remote controller to control other

manufacturers’ AV components, some buttons may

not work as expected.

• Make sure you’ve entered the correct remote control

code.

• Make sure to set the same ID on both the AV receiver

and remote controller (pages 72 and 73).

Can’t control other components?

• If it’s an Onkyo component, make sure that the

cable and analog audio cable are connected properly.

Connecting only an cable won’t work (page 37).

• Make sure you’ve selected the correct remote control-

ler mode (pages 14-19).

• If you connect an MD recorder or CD recorder to the

TAPE jacks, be sure to make the necessary setting

(pages 52 and 78).

• When learning commands, make sure that the trans-

mitting ends of both remote controllers are pointing at

each other.

• Are you trying to learn from a remote controller that

cannot be used for learning? Some commands cannot

be learned, especially those that transmit several

instructions with a single button press.

• The wrong remote control code has been entered.

• The entered remote control code may not be correct.

If more than one code is listed, try each one.

• With some AV components, certain buttons may not

work as expected, and some may not work at all.

• To control Onkyo components, point the remote con-

troller at the AV receiver.

• To control another manufacturer’s component, point

the remote controller at that component.

Can’t record?

• On your recorder, make sure the correct input is

selected (e.g., digital or analog).

Zone 2 has turned off?

• Was the Sleep function set? The Sleep function turns

off Zone 2 as well as the AV receiver. To set the Sleep

function for Zone 2 only, see page 76.

There’s no sound?

• Only components connected to analog inputs can be

played in Zone 2.

Tuner

Remote Controller

Recording

Zone 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR603E Seite 91

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR603E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info