Bedienungsanleitung Onkyo TX-SR674 (Seite 90 von 92) (Englisch)

446898

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Troubleshooting—Continued

There’s no sound

• Only components connected to analog inputs can be

played in Zone 2.

The sound changes when I connect my head-

phones

• When a pair of headphones is connected, the listening

mode is set to Stereo, unless it’s already set to Stereo,

Mono, Direct, or Pure Audio (not North American

models).

The speaker volume cannot be set as required

• When the Automatic Speaker Setup function is used,

or the volume is adjusted on the onscreen setup

menus, the maximum possible volume setting may

change.

The speaker distance cannot be set as required

• In some cases, corrected values suitable for home the-

ater use may be set automatically.

The display doesn’t work

• The display is turned off when the Pure Audio (not

North American models) listening mode is selected.

How do I change the language of a multiplex

source

• Use the “a. Multiplex” setting on the “Audio Adjust”

menu to select Main or Sub (page 73).

The functions don’t work

• To use , you must make an connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver, even if they are connected digi-

tally (page 36).

The functions Auto Power On/Standby and

Direct Change don’t work for components con-

nected via

• These functions don’t work when Zone 2 is turned on.

When performing “Automatic Speaker Setup,”

the measurement fails showing the message

“Ambient noise is too high.”

• This can be caused by any malfunction in your

speaker unit. Check if the unit produces normal

sounds.

The following settings can be made for the compo-

nent video, S-Video, and composite video inputs

You must use the buttons on the unit to make these set-

tings.

1. While holding down the input selector button for the

input source that you want to set, press the [SETUP]

button.

2. Use the Left and Right [ ]/[ ] buttons to change

the setting.

3. Press the [SETUP] button when you’ve ﬁnished.

• Video Attenuation

This setting can be made for the DVD, VIDEO 1,

VIDEO 2, VIDEO 3, or VIDEO 4 input.

If you have a games console connected to the com-

ponent video, S-Video, or composite video input,

and the picture isn’t very clear, you can attenuate the

gain.

Video ATT:0: (default).

Video ATT:2: Gain is reduced by 2 dB.

Zone 2

Others

The AV receiver contains a microcomputer for signal pro-

cessing and control functions. In very rare situations,

severe interference, noise from an external source, or

static electricity may cause it to lockup. In the unlikely

event that this happens, unplug the power cord from the

wall outlet, wait at least ﬁve seconds, and then plug it

back in again.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded cor-

rectly.

The AV receiver uses a battery-less memory backup

system in order to retain radio presets and other set-

tings when it’s unplugged or in the case of a power fail-

ure. Although no batteries are required, the AV receiver

must be plugged into an AC outlet in order to charge the

backup system.

Before disconnecting the power cord from the wall out-

let, set the AV receiver to Standby.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR674 Seite 90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR674

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info