586205
4
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
Easy installation
Generally, once the receiver is switched on, it is ready to play channels from default channel list.
If after turning on You can see only receiver’s menu, and when You try to push MENU or EXIT button, “No channels!”
information appears, it means that channel list has been erased. There are two ways to create new channel list:
Restore default channel list, or
Scan Your own channel list
Restore default channel list
To restore default channel list, explore the menu with / buttons, and select Tools menu. Press OK to enter. You
may be asked about password (default is 0000 enter using numeric buttons). Using / buttons select Factory
Setting option and press OK. Use /buttons to move cursor to “Yes“ and again confirm by OK button. After a while,
reboot receiver using POWER button.
If after above settings, channels are still not played, only “No Signal!” information appears on screen, go to next
chapter, where You can find how to configure Your satellite installation.
Configure Your satellite installation
To configure satellite installation, explore the menu with / buttons, and select Installation menu. Press OK to
enter. You may be asked about password (default is 0000 enter using numeric buttons). Using / buttons select
Antenna Connection and press OK. This menu contain only one function LNB. Using / buttons, You can select
what kind of antenna installation is connected to receiver fixed (in most situations) or motor (special dish positioning
system for this installation, refer to motor instruction manual). Select Your installation type and press MENU to back
to Installation.
Now using / buttons select Satellite List and press OK. In this menu, using / and OK buttons You can define
which satellites are available in Your installation. Next, press MENU to back to Installation.
If Your installation receive signal from more than one satellite, use / buttons to select Antenna Setup and press
OK. In satellite function use / buttons to choose satellite and in DiSEqC1.0 function You can assign selected
satellite to corresponding DiSEqC switch input. Use MENU to back to Installation. Now Your satellite installation should
be finally configured and ready to receive connected signal.
Scan Your own channel list
After satellite installation configure, You can create Your own channel list.
If You want to erase all currently existing channels, explore the menu with / buttons, and select Edit Channel
menu. Press OK to enter. You may be asked about password (default is 0000 enter using numeric buttons). Using
/ buttons select Delete All and press OK. Use /buttons to move cursor to “Yes“ and again confirm by OK
button. After a while, channel list will be empty.
Now, explore the menu with / buttons, and select Installation menu. Press OK to enter. You may be asked about
password (default is 0000 enter using numeric buttons). Using / buttons select Multi Satellite Search and press
OK. Next, using / buttons select Search and press OK. Receiver start scanning all selected previously in Satellite
List function satellites. Please, be noted his procedure may takes few minutes.
If after above procedures, Your receiver still cannot play channels, it is highly recommended to contact with Your local
professional installator or seller.
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Opticum FS 10p wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Opticum FS 10p

Opticum FS 10p Kurzanleitung - Deutsch - 8 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info