Bedienungsanleitung Orbis NEO ML plus (Seite 3 von 8) (Deutsch, Englisch, Französisch, Spanisch)

612909

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Thermostat NEO ML+

DESCRIPTIÓN:

The NEO ML+ thermostat is a user-friendly, adjustable digital electronic

thermostat.

WARNING:

Electrical appliance assembly and installation must be carried out by an

authorised installer. Before connecting to the mains, the power must be

removed from the associated wiring.

This appliance is internally protected against interference.

INSTALLATION:

The control device is independently mounted on a wall or in a

mechanism box. It is recommended that it be installed at a height of 1.5

metres.

The thermostat must be independently installed so that it free from

obstacles and is not affected by other appliances or heat sources (the

sun, radiators and windows etc).

To fix the device in place, open the cover and slide the battery

compartment cover to the right. Remove the securing base by pressing

on the tab in the battery compartment and separate it from the

appliance. Secure the base with the included screws. In order to replace

the NEO ML+ into its base, insert the upper base guides into the slots in

the apparatus and press on the lower part until the tab fits into the space

under the battery compartment cover. Replace the battery compartment

cover.

CONNECTION:

Connect the device as shown in the diagram below:

FITTING AND REPLACING BATTERIES:

The device is powered by two 1.5 V LR03 (AAA) alkaline batteries (not

included). Respect the polarity indicated inside the battery compartment.

When batteries are inserted for the first time, the screen should activate

and all display segments should appear. Battery lifetime is approximately

one year.

When battery power is running low, the symbol Lo is displayed

alternating with measured ambient temperature. The batteries should be

changed as soon as possible for continued correct operation NEO ML+

operation.

Used batteries should be disposed of in a special used-battery container.

Respect the environment.

OPERATING MODES:

This equipment automatically detects the operating mode in accordance

with how the configuration jumpers are inserted and whether an external

sensor is connected.

The configuration jumpers are inserted over the pins located at the rear

of the apparatus. The external sensor is connected to terminals 1 and 2.

IMPORTANT: It is necessary to RESET the device after changing

the configuration. To RESET the device, it must be connected to the

base .It is necessary to press the Reset button for more than 3 seconds.

- INCORRECT CONFIGURATIONS.

- If the internal or external sensor is not fitted the following will be

displayed on screen -- --. Incorrect sensor operation.

- If the external sensor is connected and Air-conditioning, the screen will

display Err, since this operation is invalid.

- HEATING-COOLING MODES

When the programming jumper is set to HEAT the thermostat is

operating in heating mode. When the load is active, this symbol

will

appear on the display.

When the programming jumper is set to COOL the thermostat is

operating in cooling mode. When the load is active, this symbol o will

appear on the display.

IMPORTANT NOTE: In cooling mode, there is a three-minute load-

activation delay.

If neither of the HEAT / COOL jumpers is inserted, the thermostat

remains in the switched-off mode, without any functions.

- MODO NORMAL MODE (internal sensor)

This mode is configured when the internal sensor jumper is fitted and no

external sensor is connected. This mode is valid for both heating and

cooling.

The following symbol is displayed on the screen when Normal Mode is

activated:

The ambient temperature corresponds to the

temperature measured by the internal sensor.

In order to enter parameter configuration in Normal Mode, press the ▲

and ▼ buttons at the same time for five seconds. Set ºC, will appear

flashing on the screen, the ▲ and ▼ buttons are used to choose

equipment operation in either º F or º C. Confirm with OK.

The symbol will now flash on the screen. Use the ▲ ▼ buttons to

select the COMFORT temperature. Confirm with OK.

The symbol will now flash on the screen. Select the ECO temperature

with the ▲ ▼ buttons. Press OK.

The word Diff. will start flashing on the screen. Use the ▲ ▼ buttons to

select the differential (the difference between the Switch On and Switch

Off temperatures) between 0.2 ºC and 1 ºC, in 0.2 °C intervals.

This mode has an anti-icing temperature set at 5 ºC, which only takes

effect when the thermostat is switched to Standby .

EXTERNAL SENSOR

HEATING/COOLING

COVER

ON / OFF / OK

CONFORT Tª

ECO Tª

BATTERY

COMPARTMENT COVER

REDUCE

INCREASE

RESET

ECO Tª

CONFORT Tª

INTERNAL SENSOR

EXTERNAL SENSOR

COOLING

HEATING

OFF

MANUAL ADJUSTMENT

CONFIGURATION

JUMPER PINS

INTERNAL SENSOR

COOLING

HEATING

INTERNAL SENSOR

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Orbis NEO ML plus Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info