Bedienungsanleitung Oregon Scientific BAR289 (Seite 6 von 12) (Englisch)

492497

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

GETTING STARTED

BATTERIES

Batteries are supplied with this product:

• Main unit 4 x UM-3 (AA) 1.5V

• Remote control 2 x UM-4 (AAA) 1.5V

• Remote sensor 2 x UM-3 (AA) 1.5V

Insert batteries before first use, matching the polarity

as shown in the battery compartment. For best results,

install batteries in the remote sensor before the main

unit. Press RESET after each battery change.

To install the main unit batteries:

To install the remote control batteries:

NOTE

UNIT

LOCATION

Main Clock / Alarm / Calendar Area

Remote Sensor Outdoor Temperature Area

REMOTE SENSOR (RTHR328N)

This product is shipped with the RTHR328N Remote

Sensor. The main unit can collect data from up to

5 sensors.

The THGR328N and THR228N sensors are also

compatible with this weather station. (Additional sensors

are sold separately. Contact your local stockist for more

information.)

The RTHR328N sensor collects temperature readings

and signals from official time-keeping organizations for

the radio-controlled clock.

Do not use rechargeable batteries.

shows when batteries are low.

It is recommended that you use alkaline

batteries with this product for longer performance.

NOTE

SENSOR SET UP

1. Open the battery compartment with a small Phillips

screwdriver and insert the batteries matching the

polarity (+ and -) as shown below.

2. Set the channel by pressing the CHANNEL button

to the required number. If you are using more than

one sensor, select a different channel for each

sensor.

3. Slide the EU / UK switch to the setting which best

suits your location.

4. Press RESET.

5. Place the sensor near the main unit.

6. Press SEARCH to manually initiate signal sending

between the sensor and the main unit. The reception

icon on the main unit will blink for approximately

3 minutes while it is searching for the sensor. (Refer

to the "Sensor Data Transmission" section for more

information.)

7. Press the °C / °F button to select the setting you want.

8. Close the remote sensor battery compartment.

9. Secure the sensor in the desired location using the

wall mount or table stand.

To fold out the stand:

For best results:

• Insert the batteries and select the unit, channel, and

radio signal format before you mount the sensor.

• Place the sensor out of direct sunlight and moisture.

• Do not place the sensor more than 30 metres

(100 feet) from the main (indoor) unit.

• Position the sensor so that it faces the main (indoor)

unit, minimizing obstructions such as doors, walls,

and furniture.

• Place the sensor in a location with a clear view to

the sky, away from metallic or electronic objects.

• Position the sensor close to the main unit during cold

winter months as below-freezing temperatures may

affect battery performance and signal transmission.

The transmission range may vary and is subject

to the receiving range of the main unit.

You may need to experiment with various locations to

get the best results.

NOTE

BAR289 ENG R5 7/28/04, 12:35 PM5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific BAR289 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific BAR289

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info