Bedienungsanleitung Oregon Scientific WMR300 (Seite 6 von 15) (Englisch)

677397

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

TRANSMITTER BOX-BATTERY INSTALLATION

The solar panel on transmitter box is an energy saving feature, which is an

environmentally friendly way to provide power to the sensors and prolongs battery

life. It can entirely provide power to the supplied rechargeable battery. Sensors

can operate entirely on the rechargeable battery power. Locate the transmitter box

under direct sunlight for power supplying by the solar panel.

The rechargeable battery from factory is not with full

battery for long time use and it probably becomes

low battery during the shipping. We recommend

you to charge it for several hours by the connected

solar panel.

You can also purchase a power adapter separately

for directly providing power to the transmitter box.

The output voltage of the power adapter is 3V.

Route the adapter cable through the cable slot.

Please check the solar panel connection. If it

is not ﬁrmly plugged, please re-connect the

solar panel:

Plug the end of color-corded connector into corresponding socket in the transmitter

box as shown below and place the wires neatly inside the box.

To install the rechargeable battery:

Insert the battery into the battery compartment, matching the polarity +/-.

polarity +

CHANNEL SETTING

Your weather station system can expand with up to 8

sets of thermometer & humidity sensors, and one of

each of wind and rain sensors, which share one main

unit to display the weather readings. You can number

each transmitter box with an independent channel ID

(1-8) by sliding the switches.

Please follow the below chart to adjust the sliding switches of SW1:

NOTE

The below 0 in the chart represents off and 1 represents on.

CH PIN 2 PIN 3 PIN 4

Channel 1 0 0 0

Channel 2 0 0 1

Channel 3 0 1 0

Channel 4 0 1 1

Channel 5 1 0 0

Channel 6 1 0 1

Channel 7 1 1 0

Channel 8 1 1 1

For obviously indicate the status of your channel, you can turn on the LED light in

the corresponding transmitter box by sliding the PIN 1 switch to 1.

Function PIN 1

Disable LED 0

Enable LED 1

After setting, please turn off the LED light by sliding the PIN 1 switch to

0 to save

power, and then close the box by tightening the screws.

NOTE

The ﬂashing LED indicates a normal transmission (See LED Light Indicator).

1 2 3 4

RSN

SW1

REMOVE SETTING

For removing the previous setting from the transmitter box, you can press RESET

and KEY at a time, then only release RESET, red light ﬂashes 5 times. Then

release KEY. The channel setting and calibrated wind direction are all removed

from the transmitter box.

LED LIGHT INDICATOR

There are three colors of LED lights in transmitter box, green, red and blue.

Different color combinations indicate different status.

Light Color Operations

Blue->green->red Flash once when you (Press and )release

RESET

Red ﬂashes every second Flash 5 times then remove setting of all the

sensors from transmitter box (See Remove

setting section)

Red Wind direction calibration

(See Direction Calibration).

Blue ﬂashes A normal transmission (WMR300A)

Green ﬂashes A normal transmission (WMR300)

SENSORS INSTALLATION

You have three options to install the sensors.

The transmitter box is capable of transmitting data wirelessly an approximate

operating range of 300m (1000 feet). Ideal placements for the sensor would be

in any location on the roof of a building that is in an open area away from trees

or other obstructions preventing from the wind ﬂow for an accurate reading.

Additionally, locate the transmitter box at the direct sunlight for power supplying

by the solar panel.

Solar panel facing: If you reside in the:

North Southern Hemisphere

South Northern Hemisphere

NOTE

Make sure the temperature and humidity sensor should be located at least

1.5 meters above the ground surface to avoid the ground temperature affecting

accuracy of the temperature and humidity sensor.

Option 1: All sensors are installed on a pole.

NOTE

Please take off the rain collector before installation and choose a pole with

the diameter that is about 32-45mm.

1. Locate one U-bolt without ﬂat washers, lock washers and hex nuts into the gap

of the rain gauge (Figure 1).

2. Let the pole fully approach to the inner of the U-bolt (Figure 2).

3. Locate the other U-bolt without ﬂat washers, lock washers and hex nuts into

the screw holes of the rain gauge (Figure 3).

4. Put the backing metal plate through the U-bolt and securely tighten two pairs of

the ﬂat washers, lock washers and hex nuts over the plate (Figure 4) by wrench.

5. Insert the two ends of the ﬁrst U-bolt into the screw holes of the wind sensor (Figure 5).

6. Tighten the other two pairs of ﬂat washers, lock washers and hex nuts on the

U-bolt of the wind sensor by wrench (Figure 6).

NOTE

Make sure the water bubble in the balance indicator on the rain gauge

stay within the circle. Check the balance status regularly for an accurate rainfall

rate reading.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific WMR300 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific WMR300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info