Bedienungsanleitung Oregon Scientific WMR90A (Seite 3 von 24) (Englisch)

796935

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Humidity / Dew Point Area

1. Dew

point level - Temperature is showing

2. HI / LO humidity and Dew Point alarms are set

3. Comfort levels

4. Humidity trend

5. MAX / MIN humidity

6. Humidity reading

WIND SENSOR

1. Wind vane measuring the wind speed

2. Wind direction sensor

3. Battery compartment

RESET

hole

5. North indicator

6. Plastic sleeve protecting the batteries

RAIN GAUGE

Base and funnel

1. Rain gauge

2. Battery compartment

RESET

button

Tipping bucket rain gauge

1. Funnel

2. Level indicator

GETTING STARTED

SET UP REMOTE WIND SENSOR

The wind sensor can take 3 readings:

• The wind speed and directions

• The outdoor temperature (Channel 1 only)

• The outdoor relative humidity (Channel 1 only)

The sensor is battery operated and is capable of transmitting data to the base station

wirelessly within an approximate operating range of 100 meters (328 feet).

NOTE

For best results, ensure that the wind direction indicator on the wind sensor

points to the North to enable an accurate reading. The sensor also should be

positioned in an open area away from trees or other obstructions.

To set

up the wind sensor main body

1. Assemble the wind direction pointer on the top of the wind sensor.

2. Use the screw (Type B) to ﬁ x.

3. Assemble the wind vanes on the top of the wind pointer.

4. Use the screw (Type B) to ﬁ x.

5. Hold the wind sensor upright and rotate the protective sleeve to the left to unlock.

6. Slide the sleeve down to open the battery compartment.

7. Insert batteries (4 x UM-3 / AA) in the compartment, matching the polarity (+ / -)

and press

RESET

8. Slide the protective sleeve up to close the compartment.

9. Rotate the sleeve to the right to lock.

To set up the wind sensor main body on an existing pole:

1. Remove the screw that ﬁ xes the plastic connector at the end of the top pole.

Remove the plastic connector by sliding it off the pole.

Insert the pole into the plastic base.

Insert the screw into the plastic base and pole and secure using the Type B

screw and washers.

Align the back of the plastic base to an existing pole.

Using the 2 U-bolts, secure the plastic base to the pole by inserting the ends of

the U-bolts into the holes on the plastic base and securing it with washers and

bolts.

Slide Integrated wind sensor into the plastic base and pole.

Insert and screw the Type “X” bolt into the hole.

9. Slide the battery cover off.

10. Using a compass, rotate and align the wind direction sensor and the NORTH

indicator line to the North.

11. Press the RESET button.

12. Slide the battery cover up

13. Rotate the sleeve clockwise to clock the cover

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific WMR90A Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info