Bedienungsanleitung Orion ORH021CW (Seite 7 von 9) (Englisch)

563016

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

www.orion.ua / support@orion.ua

Press three times for strong

16. Cool/Warm Button

Press Cool/Warm button to select warm humidification. The warm mist temperature will be about 45°.

When you choose the warm humidification, the Heat light will turn on.

17. When the Refill light turn on, it’s time to refill the water tank.

MAINTENANCE

 Always unplug the unit before servicing it in any way.

 Be careful when handling the water if warm humidification was selected. The water temperature of the

water remaining in the unit after user may be high.

 Do not submerse the unit in water, or allow water to enter anywhere on the unit except the designated

water tank.

Water tank and water basin

1. Fill water tank with 1 teaspoon of household bleach in 1 gallon of water. Let stand

twenty minutes, shaking vigorously with two hands every few minutes, drain and rinse with

clean water until the bleach smell is gone. Dry with a clean cloth or paper towel.

2. Wipe the water basin with a soft cloth dampened in the cleaner and water solution.

Rinse the water basin with cool water. When cleaning the water basin do not place the

nebulizer directly under the water tap.

DO NOT IMMERSE WATER BASIN IN WATER.

3. Wipe all exteriors surfaces of the base with a soft, dry cloth. Do not immerse the base in

water or use water to clean the base. As with any electrical appliance, an electric shock

may result or the humidifier may be damaged.

Note: Clean the inside of the water tank at least once a week

Ultrasonic disk

There may be some lime deposits in the nebulizer, Particularly in areas with hard water. Overcome this

drawback by cleaning the nebulizer with water and vinegar on a soft cloth regularly, as follows:

1. Dampen a cloth with vinegar and wipe the nebulizer gently, until the lime deposits disappear completely.

2. Rub down gently with a dry cloth and remove remains of humidity

3. Do not rub the nebulizer with solid objects.Do not clean with chemical products.

Air filter

1. Gently wipe away debris from the filter with a soft cloth.

Water level sensor

The water level sensor is made of three key parts. When cleaning DO NOT MISPLACE these parts and MAKE

SURE that you assemble these three parts correctly after cleaning and before operating humidifier. They are as

follows:

Plastic Cap-this part has 4 flat tabs coming out form the bottom and is placed on top of a plastic pin.

Water Float- a small round part resembling a “life saver” candy located underneath the Plastic Cap.

Pin-plastic pin that secures water float and plastic cap.

To clean the water float unscrew the plastic cap from the pin. Remove the water float and clean by wiping the

parts with a soft damp cloth. Replace the parts by first putting the water float onto the pin and re-screwing the

plastic cap onto pin.

Water Level Sensor

Water Float Plastic pin

Plastic Cap

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Orion ORH021CW Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info