MAXrun
(instead of three). Also, the Lo BATT
warning appears in Sport mode on the
watch display when a workout starts
or stops.After 30 minutes of inactivity,
the foot pod automatically powers off to
conserve the battery (LED blinks twice
TO REPLACE THE BATTERY:
1 Locate the circular battery cover on
the back of the foot pod.
2 Use a coin to twist the cover counter-
clockwise until it is loose enough to
remove.
3 Remove the cover and replace the
battery with the positive side facing up.
NOTE: Be careful not to damage or lose
the o-ring gasket on the cover.
4 Use a coin to twist the cover back
into place.
NOTE: You do not need
to repeat pairing or cal-
bration following replace–
ment. Calibrating your foot
pod is optional and can
im- prove accuracy. If you
want to improve use
the instruction manual
of the MIXpro and follow
the instruction. There are
two ways to adjust the
calibration: auto/manual.
SENSOR PCBA SPECIFICATIONS:
PCB size: 42 mm x 10 mm
PCB weight: ~ 3 g
Power: Single user-replaceable coin
cell battery (CR2032)
Battery life: >200 hrs run time
(at room temp)
Storage temp: -40°C to +70°C
Operating temp: -20°C to +60°C
Sensor Accuracy Range: 0°C to +40°C
Speed-distance computation:
Dynastream patented single accelero-
meter technology
Available data: Speed, distance, cadence
Speed range: 1.0-5.5 m/s (3.6-19.8 km/hr)
Calibrated speed/dist accuracy:
Walk 97%, Jog 98%, Run 97%,
median accuracy
Uncalibr. speed/dist accuracy:
Walk 95%, Jog 95%, Run 95%,
median accuracy
Instantaneous cadence accuracy:
+/- 1 stride/min
User-interface: auto on/off
LED Operation: blinking when initially
activated, non-blinking afterward
RF SPECIFICATIONS:
Transmission Protocol: 2.4 GHz using
ANT+SPORT™
Peak transmitter power:
0.0 dBm ±4.0 dBm
Average Transmitter Power: -
4.0 dBm ±4.0 dBm
Message Rate: 4 Hz
Typical communication range:
> 3 m (dependent on watch receiver)
Regulatory compliance: FCC, IC, ETSI
Mechanical Specifications: Foot Pod Size:
57 (L) x 38 (W) x 13.5 (H) mm
Foot Pod Weight: 27g (including battery)
Attachment Method: Securely attaches
to laces using one-piece clip
Materials: BS (case), PA-12 + GF
(battery door), PC (clip)
Water resistance: -0.5 ATM to +1.0 ATM
FEATURES:
ANT™ RF Technology, using 2.4 GHz Glo-
bal ISM band. Compatible with o-synce
MIXpro proven Speed and Distance
Monitor watch technology for running
MAXrun FOOT POD
You can combine this food pod sensor
with the MIXpro watch. For more infor-
mation visit the o-synce web site.
The foot pod is on standby and ready
to send data. As soon as you install the
foot pod and start moving, the foot pod
sends data to the watch.
1 Press the tabs on the lace clip. Lift
and separate the foot pod from the
lace clip.
2 Loosen your shoe laces slightly.
3 Thread the lace clip through 2–3
secure sections of your shoelaces,
allowing enough room at the top to
tie the shoelaces as usual.
4 Tie your shoelaces securely to keep
the foot pod in place during your
workout.
5 Snap the foot pod into the lace clip.
The foot pod must be pointed toward
the front of your shoe.
6 Take a few steps to activate the foot
pod. The LED blinks three times.
7 Bring the MIXpro watch within range
(3 m) of the foot pod.
8 Press C to access SPORT mode.
The foot pod icon appears on the
SPORT page.
9 Press B to access the DIST, LAP,
or SPEED/PACE data pages.
10 If the foot pod data does not appear,
you may have to pair the foot pod
and the watch again.
BATTERY LIFETIME
When there is approximately five hours
of foot pod battery life remaining, the
LED blinks six times when activated
O
P
E
N
