683927
2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
BA 873040led N;DE,GB -23435- 2016.11V02
INSTRUCTION MANUAL DIMMER [LED STRIPES]
Technical Features Safetey instructions
Supply voltage 12 – 48 VDC*
CAUTION!! DANGER OF LIFE / RISK OF FIRE AND ELECTRIC SHOCK!!
Power consumption 0,5 VA
Suitable type of lamps Dimmable LED lamps
Maximum load 8A
Installation and assembly of electrical equipment must be carried out only by professional electrician!
Connect the supply voltage/frequency as stated on the product!
Disconnect device from power supply for wiring and installation purposes!
Check power supply is disconnected!
Defective devices have to be put out of service immediately
No safe electrical isolation between the power supply and pushbutton 2!
When using a 230V~ pushbutton on P
L
und P
N
no low voltage protection, no SELV!
Warranty void if housing opened by unauthorized person!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if
external influences exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with local building and electrical codes
Max. number of pushbuttons Unlimited (non-lighted pushbuttons)
Pushbutton 1 Pushbutton referred to Ground
Optional: Pushbutton 2 Pushbutton referred to 230V~ (no SELV)
Dimensions 46 x 42 x 13 mm
Weight 23 g
Permitted ambient temperature
Storage temperature
0º … +40ºC
-30º … +70ºC
Type of protection IP20 according to DIN EN 60529
*NOTE: The power supply associated with this dimmer should comply with the Low Voltage Directive 2006/95/EC and EMC
Directive 2004/108/EC
Important Note
For all lamps, please take into account the specifications of the manufacturer!
Description / Installation / Operation Wiring diagram
Description / Intended use
Dimmer for LED lamps 12 - 48VDC up to 6A, with Pulse Width Modulation technology (PWM),
specially designed for 1-channel LED strips.
Small size dimmer, for flush-mounting (e.g. behind standard pushbutton).
Protected against overload and short circuit. Built-in heat protection.
Can be used with a pushbutton referred to Ground (Pushbutton 1) or a pushbutton referred to 230V~ (Pushbutton 2) or both.
When using a 230V~ pushbutton on P
L
und P
N
the low voltages are not SELV!
With or without memory function.
With two function rotary switches:
min: minimum brightness level (1% up to ~60%).
dim speed: dimming speed between 3 and 10 sec. (from 0 to 100%).
Installation
1 Disconnect installation from power supply and check that power supply is disconnected.
2 Install the dimmer according to the wiring diagram.
3 Make sure the loads are connected properly and reconnect power supply.
4 Press shortly the pushbutton to switch the lamps on and dim with a long press to the minimum brightness level.
5 If you like the change the minimum brightness level you have to disconnect the installation again from power supply and set
with the rotary switch (min) the desired minimum brightness level.
.
Operation
Press shortly the pushbutton to switch the lamps on and off!
=> Switch on „No Mem“ = Lamp(s) switches on with max. brightness.
=> Switch on „Mem“ = Lamp(s) switches on with the brightness of the last switch off
With a long press you can dim!
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Paladin 873 040 led wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info