683986
2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
BA 873 041amp N;DE,GB -23818- 2017.04V01
INSTRUCTION MANUAL AMPLIFIER FOR LED-STRIPS
Safety instructions
Supply voltage 12 24V DC
CAUTION!!
DANGER OF LIFE / RISK OF FIRE AND ELECTRIC SHOCK!!
Power consumption <12mA
Suitable type of lamps LED-strips
Maximum load 8A
Installation and assembly of electrical equipment must be carried out only by professional electrician!
Connect the supply voltage/frequency as stated on the product!
Disconnect device from power supply for wiring and installation purposes!
Check power supply is disconnected!
Defective devices have to be put out of service immediately!
Warranty void if housing opened by unauthorised person!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if
external influences exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with local building and electrical codes!
Dimensions 46 x 42 x 13 mm
Weight 23 g
Permitted ambient temperature
Storage temperature
0º … +40ºC
-30º … +70ºC
Type of protection IP20 according to DIN EN 60529
Important Note
Conformity with Standard DIN EN 60669-2-1
For all transformers and lamps, please take into account the specifications of the manufacturer!
Wiring diagram
Amplifier for one-color 12-24 V DC LED Strips up to 8A.
With connectors for easy wiring of the in- and output.
The amplifier could be installed in every standard flush-mounted box.
Protection against overload, short circuit and overheat.
The amplifier allows to increase the meters of LED strips, without brightness losses, which are
controlled by only one dimmer.
For all transformers and lamps, please take into account the specifications of the
manufacturer!
Overview of the wiring
The amplifier has two inputs and one output:
1. Input of the first LED-strip. This input will be also used, if a dimmer will be installed.
2. The supply voltage of the amplifier (12-24 V DC with stabil voltage).
3. Output of the following LED-strip.
Installation
1 Disconnect installation (also the dimmer) from power supply and check that power supply is
disconnected
2 Install the amplifier according to the wiring diagram.
3 Make sure the loads are connected properly and reconnect power supply.
Wiring diagram with dimmer (paladin 873 040led)
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Paladin 873 041 amp wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info