Bedienungsanleitung Paladin 879 410 led (Seite 2 von 2) (Englisch)

683929

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

BA 879 410-led HM; DE, GB - 23642 - 2016.05-V01

Hugo Müller GmbH & Co KG│Sturmbühlstraße 145-149│D-78054 VS-Schwenningen│Tel.: +49 (0) 7720 80 836│Fax: +49 (0) 7720 31 083│info@hugo-mueller.de│www.hugo-mueller.de

INSTRUCTION MANUAL TRIAC DIMMER [R,L] – 879 410 LED

Operating modes Operating modes

Operation with pushbutton



Pressing the pushbutton shortly turns the load on and off.



Pressing the pushbutton for a long time carries-out a cyclical dimming (as long as the

pushbutton is pressed).

In this operation mode the internal potentiometer defines the lower dimming limit (pushbutton

MEM, NO MEM or MEM PLUS). It avoids flickerings or undesired switching-offs.

Operation with external potentiometer (galvanically isolated)



It is possible to control the load with a 10 kΩ potentiometer.



At the minimum level of the potentiometer the load stays turned off.



By turning the potentiometer, the load increases.



It is necessary to set the built-in potentiometer at minimum.

Operation with internal potentiometer



It is possible to control the load with the internal potentiometer of the dimmer.



By setting the potentiometer to the minimum value, the use of an external potentiometer is

possible.



If you put the potentiometer to any value higher than the minimum value, the potentiometer

will only consider this value. It will ignore the signals of the external potentiometer.

Operation with signal 0 - 10V (galvanically isolated)



0V correspond to a switched off status.



10V correspond to the maximum illumination of the dimmer.

You can use any external, isolated or not isolated voltage source

with 0 - 10 V (SPS, control panel etc.).

In this mode of operation the internal potentiometer defines the minimum dimming level. It avoids

flickerings or undesired switching-offs.

Master-Slave-configuration (galvanically isolated)

This configuration is used, if the maximum load that is supported by one dimmer is exceeded. With

this configuration it is possible to distribute the load across multiple dimmers and extend the load. For

this it is necessary to spread the load into several partial loads with each dimmer controlling its

maximum load. It is also recommended to use slaves in applications where different loads have to be

controlled. In this mode of operation the internal potentiometer defines the minimum dimming level. It

avoids flickerings or undesired

switching-offs.

Example 1 Example 2 Example 3 Example 4 Example 5

Operation with pushbutton

Place the selector switch in the

desired working mode:

 MEM to switch on at the

same level as turned off.

 NO MEM to switch on

with maximum power.

 MEM PLUS to switch on

at the same level as

turned off and to rebuild

the operating status (turn

on/ off or level of

intensity) after power

failure.

Operation with pushbutton, extended by

slaves



The MASTER dimmer must be set

according to example 1.To configure a

dimmer as SLAVE, the selector switch

must be in SLAVE mode.



It is possible to add an unlimited number

of slaves.



There can be a time delay in the

response if you use a large number of

salves.



The heat development in the installation

box has to be monitored, especially when

using a larger number of dimmers.



It is recommended to realize a spacing

between each dimmer (1 module

spacing).

Operation with potentiometer



The selector switch must be in the

correct position for the

potentiometer



The brightness level depends on the

position of the potentiometer.



Turning the potentiometer clockwise

will increase the light intensity.

A) Operation with ext. potentiometer

B) Operation with int. potentiometer

Operation with 0 - 10V

signal



The selector switch

must be in the

correct position 0 -

10V.



Level 0V

corresponds to the

status switched off.

The light intensity

increases in the

same amount as the

voltage does to 10V.

3-phase-installation controlled by potentiometer

and increased by slaves



Do the installation according to the wiring diagram.



The MASTER dimmer must be configured as in

example 3A. The slaves must be in position SLAVE.



It is recommended to distribute the loads between

the three phases.



In case of three-phase line without electrical neuter,

please contact us.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Paladin 879 410 led Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Paladin 879 410 led

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info