Bedienungsanleitung Panasonic ey 6220 d dr (Seite 4 von 34) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

387517

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Main switch (ON/OFF)···(E)

Push the upper half of the switch for forward

( ) rotation, or the lower half for reverse

( ) rotation.

(Refer figure 5)

Speed selector switch···(C)

To suit the application of this tool, two

different rotational speeds are available.

Depending upon use, either the high or low

speed should be selected.

LOW

HIGH

200min

-1

(RPM)

400min

-1

(RPM)

strong torque

less torque

CAUTION: Check rotational speed selection

before operating this tool.

(Refer figure 6)

Main switch lock···(D)

After use, set the main switch lock at the lock

position to prevent accidental operation.

(Refer figure 7)

Battery pack (EY9221)···(F)

Appropriate Use of Battery Pack

Ni-MH Battery Pack

• Charge the Ni-MH battery fully before

storage in order to ensure a longer service

life.

• The ambient temperature range is between

0˚C (32˚F) and 40˚C (104˚F). If the battery

pack is used when the battery temperature

is below 0˚C (32˚F), the tool may fail to

function properly. In that case, charge the

battery until charging is completed for

appropriate functioning of the battery.

• When battery pack is not in use, keep it

away from other metal objects such as

paper clips, coins, keys, nails, screws, or

other small metal objects that can make a

connection from one terminal to another.

Short-circuiting the battery terminals

together may cause sparks, burns or a fire.

• When operating with a Ni-MH battery pack,

make sure the area is well ventilated.

Battery Pack Life

The rechargeable batteries have a limited life.

If the operation time becomes extremely short

after recharging, replace the battery pack with

a new one.

OPERATION

Hexagonal driving shaft···(A)

NOTE: When attaching or removing bit, be

sure to set the main switch lock at the

lock position.

Select the suitable bit and lightly push it into

the hexagonal driving shaft of the main unit.

(Refer figure 2)

Refer figure 2 for useable bits.

Clutch handle···(B)

When using the tool for driving screws into

soft material or for terminal screws, etc., there

is the possibility of damaging the material or

threads if the torque is too high. To

compensate for this, the clutch torque may be

adjsuted by turning the clutch handle to the

required setting.

Clutch position 1 is the minimum and the

clutch torque increases with positions 2, 3, 4,

and 5. When the device is set at position 6,

the clutch will not slip and the connection to

the motor will be direct.

CAUTION: If the battery pack loses its power

during usage, the clutch may not

slip even at positions 4 or 5, if this

occurs, recharge the battery pack.

(Refer figure 3)

Bit locking function

With the switch at off, the bit is locked in place,

and the tool can be used as a manual screw-

driver.

There will be a little play in the driving shaft,

but this is not a malfuncton.

CAUTION: Exact torque should be verified

with a torque wrench for precise

limits as the screw can be

damaged.

(Refer figure 4)

P05-11(EY6220EN).qxd 10.7.6 16:49 ページ 6

2. Select the current battery dock (Li-ion Battery

pack or Ni-MH Battery pack) cover. Slide the

battery dock cover to allow insertion.

3. Insert the battery pack firmly into the charger.

4. During charging, the charging lamp will be lit.

When charging is completed, an internal

electronic switch will automatically be triggered

to prevent overcharging.

• Charging will not start if the battery pack is

warm (for example, immediately after heavy-

duty operation). The orange standby lamp will

be flashing until the battery cools down.

Charging will then begin automatically.

5. The charge lamp (green) will flash slowly once

the battery is approximately 80% charged. (Li-

ion Battery Only)

6. When charging is completed, the charging lamp

in green color will turn off.

7. If the temperature of the battery pack is 0˚C or

less, charging takes longer to fully charge the

battery pack than the standard charging time.

Even when the battery is fully charged, it will

have approximately 50% of the power of a fully

charged battery at normal operating

temperature.

8. Consult an authorized dealer if the charging

lamp (green) does not turn off.

9. If a fully charged battery pack is inserted into

the charger again, the charging lamp lights up.

After several minutes, the charging lamp in

green color will turn off.

Battery Recycling

ATTENTION: For environmental protection

and recycling of materials, be

sure that it is disposed of at an

officially assigned location, if

there is one in your country.

Battery charger (EY0L11)···(H)

Charging

Common Cautions for the Li-ion/Ni-MH Battery

Pack

NOTE: • When a cold battery (of about 0˚C or

less) is to be charged in a warm

room, leave the battery in the room

for at least one hour and charge it

when it has warmed up to room

temperature. (Failing to do so may

result in less than a full charge.)

• Cool down the charger when

charging more than two battery

packs consecutively.

• Do not insert your fingers into

contact hole, when holding charger

or any other occasions.

• When charging continuously, wait

about 5 seconds after removing one

battery pack before inserting the

next.

CAUTION: To prevent the risk of fire or

damage to the battery charger.

• Do not use power source from

an engine generator.

• Do not cover vent holes on the

charger and the battery pack.

• Unplug the charger when not in

use.

Li-ion Battery Pack

NOTE: Your battery pack is not fully charged

at the time of purchase. Be sure to

charge the battery before use.

Ni-MH Battery Pack

NOTE: When you charge the battery pack for

the first time, or after prolonged

storage, charge it for about 24 hours to

bring the battery up to full capacity.

Battery charger

1. Plug the charger into the AC outlet.

NOTE: Sparks may be produced when the

plug is inserted into the AC power

supply, but this is not a problem in

terms of safety.

To AC

outlet

Pictured:

Ni-MH Battery Pack

P05-11(EY6220EN).qxd 10.8.18 13:39 ページ 7

Refine_10-08-18 16:12:10

Refine_EY6220.07.p1.pdfRefine_EY6220.06.p1.pdf

Refine_10-08-18 10:30:43

B536502_EY6220_Tori_EU 4 10-08-23 15:56:41

Panasonic ey 6220 d dr Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info