Bedienungsanleitung Panasonic rx d21 eg a (Seite 3 von 8) (Englisch)

407518

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

RQT6744

Switch [ ] to “TUNER”.

(Unit comes on.)

Press [BAND] to select “FM” or “AM”.

(Omit this step if using the remote control)

If “ ” is on the display, press

[TUNE MODE] to clear it off.

Press [–/g] or [f/+] to

tune to the desired station.

The frequency changes one step

each time a button is pressed.

Automatic tuning

Keep [–/

g] or [f/+] depressed and release when the frequency

display starts to change. A station with good reception is automati-

cally selected and the process stops.

To stop automatic tuning, press [–/

g] or [f/+] again.

Note

Automatic tuning may stop on a frequency where there is no station if

there is interference. Press [–/

g] and [f/+] to tune if this occurs.

Adjust the volume.

To use auto scan

You can search for a station by listening to all tuned-in stations for 8

seconds each.

Preparation: Switch [

] to “TUNER”.

1. Press [BAND] to select “FM” or “AM”.

2. Press [AUTO SCAN].

Auto scan starts.

3. Press [AUTO SCAN] when you find the desired station.

Auto scan ends when it reaches the original frequency again.

To stop during the process, press [AUTO SCAN].

To improve reception

FM: Extend the whip antenna and adjust its direction.

AM: Adjust facing of the unit.

If noise is excessive in the FM stereo mode

Press [FM MODE]. (“

” lights up.)

Sound will be produced in monaural, but this also reduces noise.

Press the button again to cancel. (“

” goes out.)

Preset the stations (twelve FM and twelve AM) to make tuning simpler.

Preparation: Tune to the desired station.

(Do steps 1–4 on the left.)

Press [MEMORY].

While “ ” and the frequency are

flashing

Press [MEMORY].

While “ ” and the preset channel

are flashing

Press [–/g] or [f/+] to

select the desired channel.

(Remote control: [

4] or [

3])

Press [MEMORY].

(This completes presetting.)

Repeat the above to preset other stations.

Note

If “

” goes off during presetting, return to step 1.

Press [BAND] to select “FM” or “AM”.

(Omit this step if using the remote control)

Press [TUNE MODE] to display

“

”.

Press [–/

g] or [f/+] to select

the desired channel (1–12).

(Remote control: [

4] or [

3])

To use preset scan

You can search for a station by listening to all preset channels for 8

seconds each.

1. Do steps to above.

For remote control, replace [– /

g] or [f/+] described below with [

or [

3].

2. Press and hold [–/

g] or [f/+] until “PS” appears on the display.

3. Press [–/

g] or [f/+] when you find the desired channel.

Preset scan ends after searching through each preset channel once.

To stop during the process, press [–/

g] or [f/+].

Normal tuning Preset tuning

The Radio

To listen to preset channels

How to preset

Indicates

auto scan

Indicates

preset scan

“ ” lights when an FM stereo

broadcast is being received.

Preset channel

15 4

124 3

P3-4 11/20/02, 11:25 AM3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic rx d21 eg a Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic rx d21 eg a

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info