618385

Panasonic SC-PM250B Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Overview of controls
Do the procedures with the remote control. You can also use the buttons on the main unit if they are the same.
A Standby/on switch [`], [1]
Press to switch the unit from on to standby mode or
vice versa. In standby mode, the unit is still consuming
a small amount of power.
B Select the audio source
On the remote control:
Press the corresponding button to select the source.
On the main unit:
C Basic playback control
D View the setup menu
E View the content information
F Select or confirm the option
G Open or close the disc tray
H Decrease the brightness of the display panel
To cancel, press the button again.
I Adjust the volume level
J Mute the sound
To cancel, press the button again.
“MUTE” is also cancelled when you adjust the volume
or when you switch off the system.
K View the play menu
L Select the sound effects
M Display panel
N Remote control sensor
Distance: Within approximately 7 m
Angle: Approximately 20° up and down, 30° left and
right
O USB port ( )
P Disc tray
Q Select “BLUETOOTH” as the audio source
To start Bluetooth
®
pairing, press and hold the button.
Preparing the remote control
Use alkaline or manganese battery.
Install the battery so that the poles (+ and –) align with
those in the remote control.
(not supplied)
RQT0A08-B_en.fm Page 10 Thursday, March 5, 2015 9:44 AM
Preparing the media
Disc
1 Press [CD x] (main unit: [x OPEN/CLOSE]) to open
the disc tray.
Put in a disc with the label facing up.
Press again to close the disc tray.
2 Press [USB/CD] to select “CD”.
USB
1 Reduce the volume and connect the USB device to
the USB port.
Hold the main unit when connecting or disconnecting
the USB device.
2 Press [USB/CD] to select “USB”.
Note:
Do not use a USB extension cable. The system cannot
recognise USB device connected through a cable.
Bluetooth
®
You can connect and play an audio device wirelessly
through Bluetooth
®
.
Preparation
• Switch on the Bluetooth
®
feature of the device and put
the device near the system.
• Read the operating instructions of the device for details.
█ Pairing a device
Preparation
If this system is connected to a Bluetooth
®
device,
disconnect it (Z“Disconnecting a device”).
1 Press [ ].
If “PAIRING” is shown, continue with step 4.
2 Press [PLAY MENU] to select “PAIRING”.
Or press and hold [ –PAIRING] on the main unit until
“PAIRING” is shown. Continue with step 4.
3 Press [R, T] to select “OK? YES” and then press
[OK].
“PAIRING” is shown.
To cancel, select “OK? NO”.
4 Select “SC-PM250” from the Bluetooth
®
menu of the
device.
If prompted for a passkey, input “0000”.
The device connects with this system automatically
after pairing is complete.
The name of the connected device is shown for a few
seconds.
Note:
You can pair up to 8 devices with this system. If a 9th device is
paired, the device that has not been used for the longest time
will be replaced.
█ Connecting a device
Preparation
If this system is connected to a Bluetooth
®
device,
disconnect it (Z“Disconnecting a device”).
1 Press [ ].
“BLUETOOTH READY” is shown.
2 Select “SC-PM250” from the Bluetooth
®
menu of the
device.
The name of the connected device is shown for a few
seconds.
3 Start playback on the device.
Note:
• A device must be paired to connect.
• This system can only connect to one device at a time.
• When
“BLUETOOTH” is selected as the source, this
system will automatically try to connect to the last
connected device.
█ Disconnecting a device
1 Press [ ].
2 Press [PLAY MENU] repeatedly to select
“DISCONNECT?”.
3 Press [R, T] to select “OK? YES” and then press
[OK].
“BLUETOOTH READY” is shown.
To cancel, select “OK? NO”.
Using the main unit
Press and hold [ –PAIRING] until “PAIRING” is shown.
Note:
A device is disconnected when you:
• Select a different source.
• Move the device out of the maximum range.
• Disable the Bluetooth
®
transmission of the device.
• Switch off the system or the device.
USB device
(not supplied)
RQT0A08-B_en.fm Page 11 Thursday, March 5, 2015 9:44 AM
Media playback
The following marks indicate the availability of the feature.
Basic playback
CD USB BLUETOOTH
Note:
Depending on the Bluetooth
®
device, some operations may
not work.
Viewing available information
CD USB BLUETOOTH
You can view the available information on the display
panel.
Press [DISPLAY].
Note:
• Maximum characters that can be shown: approximately 32
• This system supports ver. 1.0, 1.1 and 2.3 ID3 tags.
• Text data that the system does not support can show
differently.
• Example: MP3 album and track number display.
Play menu
CD USB
1 Press [PLAY MENU] repeatedly to select
“PLAYMODE” or “REPEAT”.
2 Press [R, T] to select the setting and then press
[OK].
Note:
• During random playback, you cannot skip to tracks which
have been played.
• The setting is cancelled when you open the disc tray.
CD :
USB :
BLUETOOTH :
CD-R/RW in CD-DA format or with MP3 files.
USB device with MP3 files.
Bluetooth
®
device.
Play Press [4/9].
Stop Press [8].
USB
The position is memorised.
“RESUME” is shown.
Press again to stop fully.
Pause Press [4/9].
Press again to continue playback.
Skip Press [2/3] or [5/6] to skip track.
CD USB
Press [R, T] to skip MP3 album.
Search Press and hold [2/3] or [5/6].
Album
number
Track
number
PLAYMODE
OFF
PLAYMODE
Cancel the setting.
1-TRACK
1TR
Play one selected track.
Press [2/3] or [5/6] to
select the track.
1-ALBUM
1ALBUM
Play one selected MP3 album.
Press [R, T] to select the MP3 album.
RANDOM
RND
Play all tracks randomly.
1-ALBUM
RANDOM
1ALBUM RND
Play all tracks in one selected MP3
album randomly.
Press [R, T] to select the MP3 album.
REPEAT
OFF REPEAT Cancel the setting.
ON REPEAT Repeat playback.
RQT0A08-B_en.fm Page 12 Thursday, March 5, 2015 9:44 AM
Link mode
BLUETOOTH
You can change the link mode to suit the connection type.
Preparation
If this system is connected to a Bluetooth
®
device,
disconnect it (Z“Disconnecting a device”).
1 Press [PLAY MENU] repeatedly to select
“LINK MODE”.
2 Press [R, T] to select the mode and then press [OK].
Note:
Select “MODE 1” if the sound is interrupted.
Input level
BLUETOOTH
You can change the input level setting if the sound input
level of the Bluetooth
®
transmission is too low.
1 Press [PLAY MENU] repeatedly to select
“INPUT LEVEL”.
2 Press [R, T] to select the level and then press [OK].
Note:
Select
“LEVEL 0” if the sound is distorted.
█ Note on disc
• This system can play CD-R/RW with CD-DA or MP3
format content.
• Before playback, finalise the disc on the device it was
recorded on.
• Some CD-R/RW cannot be played because of the
condition of the recording.
█ Note on USB device
• This system supports USB 2.0 full speed.
• This system can support USB devices of up to 32 GB.
• Only FAT 12/16/32 file system is supported.
█ Note on MP3 file
• Files are defined as tracks and folders are defined as
albums.
• Tracks must have the extension “.mp3” or “.MP3”.
• Tracks will not necessarily be played in the order you
recorded them.
• Some files can fail to work because of the sector size.
MP3 file on disc
• This system can access up to:
– 255 albums (including root folder)
– 999 tracks
– 20 sessions
• Disc must conform to ISO9660 level 1 or 2 (except for
extended formats).
MP3 file on USB device
• This system can access up to:
– 800 albums (including root folder)
– 8000 tracks
– 999 tracks in one album
MODE 1 Emphasis on connectivity.
MODE 2
(default)
Emphasis on sound quality.
(default)
RQT0A08-B_en.fm Page 13 Thursday, March 5, 2015 9:44 AM
Radio
Preparation
Press [RADIO] to select “FM”.
Manual tuning
1 Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
2
Press [
R
,
T
] to select “MANUAL” and then press [OK].
3 Press [2/3] or [5/6] to tune in to the
station.
To tune automatically, press and hold the button until
the frequency starts changing quickly.
“STEREO” is shown when a stereo broadcast is being
received.
Memory presetting
You can preset up to 30 FM stations.
█ Automatic presetting
1 Press [PLAY MENU] to select “A.PRESET”.
2
Press [
R
,
T
] to select the setting and then press [OK].
The tuner presets all the stations it can receive into the
channels in ascending order.
To cancel, press [8].
█ Manual presetting
1 Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
2
Press [
R
,
T
] to select “MANUAL” and then press [OK].
3 Press [2/3] or [5/6] to tune in to the
station.
4 Press [OK].
5 Press [R, T] to select a preset number and then
press [OK].
Do steps 3 through 5 again to preset more stations.
The new station replaces any station that occupies the
same preset number.
█ Selecting a preset station
1 Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
2
Press [
R
,
T
] to select “PRESET” and then press [OK].
3 Press [2/3] or [5/6] to select the preset
station.
Improving the sound quality
1 Press [PLAY MENU] repeatedly to select
“FM MODE”.
2 Press [R, T] to select “MONO” and then press [OK].
To cancel, select “STEREO”.
“MONO” is also cancelled when you change the
frequency.
To memorise the setting
Continue with step 4 of “Manual presetting”.
Checking the signal status
Press [DISPLAY].
LOWEST Tuning begins from the lowest frequency.
CURRENT Tuning begins from the current frequency.
FM – – – – The FM signal is in monaural.
The system is not tuned in to a station.
FM ST The FM signal is in stereo.
FM MONO “MONO” is selected as the “FM MODE”.
RQT0A08-B_en.fm Page 14 Thursday, March 5, 2015 9:44 AM
DAB+
Preparation
Press [RADIO] to select “DAB+”.
Note:
If you select
“DAB+” for the first time, the system will tune
automatically.
Manual tuning
1 Press [PLAY MENU] repeatedly to select
“MANUAL SCAN”.
2 Press [R, T] to select the frequency block and then
press [OK].
If no station is detected, “SCAN FAILED” is shown.
Adjust the antenna and try again.
To tune automatically
1 Press [PLAY MENU] to select “AUTOSCAN” and
then press [OK].
“START?” is shown.
2 Press [OK] to start tuning.
“DAB AUTO SCAN” is shown.
If no station is detected, “SCAN FAILED” is shown.
Do manual tuning.
Note:
Preset frequencies are erased after you do automatic tuning.
Memory presetting
You can preset up to 20 stations.
1 Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
2 Press [R, T] to select “STATION” and then press
[OK].
3 Press [2/3] or [5/6] to tune in to the
station.
4 Press [OK].
5 Press [R, T] to select a preset number and then
press [OK].
Do steps 3 through 5 again to preset more stations.
The new station replaces any station that occupies the
same preset number.
Note:
You cannot preset a station when the station is not
broadcasting or when you have selected a secondary service.
█ Selecting a preset station
1 Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
2 Press [R, T] to select “PRESET” and then press
[OK].
3 Press [2/3] or [5/6] to select the preset
station.
Secondary service
You can listen to secondary services when “ ” is shown.
1 Press [PLAY MENU] repeatedly to select
“DAB SECONDARY”.
2 Press [R, T] to select the secondary service and
then press [OK].
To cancel, select “PRIMARY”.
Note:
The setting is cancelled when you select other stations.
Viewing available information
You can view the following information on the display
panel:
• Information about the DAB broadcast
• Programme type
• Ensemble label
• Frequency
• Time
Press [DISPLAY].
Checking the signal quality
You can check the signal quality when adjusting the
antenna.
1 Press [PLAY MENU] repeatedly to select
“SIGNAL QUALITY” and then press [OK].
The frequency block followed by the reception quality
is shown.
To select other frequency blocks, press [R, T].
2 Press [OK] again to exit.
Automatic clock adjustment
You can set the clock to update automatically.
1 Press [PLAY MENU] repeatedly to select
“AUTO CLOCK ADJ”.
2 Press [R, T] to select “ON ADJUST” and then press
[OK].
To cancel, select “OFF ADJUST”.
Frequency
block
Frequency Reception quality
0 (poor) to 8 (excellent)
RQT0A08-B_en.fm Page 15 Thursday, March 5, 2015 9:44 AM
Clock and timers
Setting the clock
This is a 24-hour clock.
1 Press [SETUP] repeatedly to select “CLOCK”.
2 Press [R, T] to set the time and then press [OK].
To check the time
Press [SETUP] repeatedly to select “CLOCK” and then
press [OK].
In standby mode, press [DISPLAY].
Note:
Reset the clock regularly to maintain accuracy.
Sleep timer
The sleep timer switches off the system after the set time.
1 Press [SETUP] to select “SLEEP”.
2 Press [R, T] to select the setting (in minutes) and
then press [OK].
To cancel, select “OFF”.
Note:
• The remaining time is always shown on the display. The
display changes temporarily when you perform other
operations.
• The sleep timer can be used together with the play timer.
• The sleep timer always comes first. Be sure not to set an
overlap of timers.
Play timer
(Except for Bluetooth
®
source)
You can set the timer to come on at a certain time to wake
you up.
Preparation
Set the clock.
1 Press [SETUP] repeatedly to select “TIMER ADJ”.
2 Press [R, T] to set the start time and then press
[OK].
3 Do step 2 again to set the end time.
4 Press [R, T] to select the source you want to play
and then press [OK].
To start the timer
1 Press [SETUP] repeatedly to select “TIMER SET”.
2 Press [R, T] to select “SET” and then press [OK].
“#” is shown.
To cancel, select “OFF”.
The system must be switched off for the timer to
operate.
To check the setting
Press [SETUP] repeatedly to select “TIMER ADJ” and
then press [OK].
In standby mode, press [DISPLAY] two times.
Note:
• The timer starts at a low volume and increases gradually to
the preset level.
• The timer comes on at the set time every day if the timer is
on.
• If you switch off the system and then switch on again while a
timer is in operation, the timer will not stop at the end time.
RQT0A08-B_en.fm Page 16 Thursday, March 5, 2015 9:44 AM
Sound effects
1 Press [SOUND] repeatedly to select the sound
effect.
2 Press [R, T] to select the setting and then press
[OK].
Others
Auto off
This system automatically switches off when you do not
use it for 20 minutes.
1 Press [SETUP] repeatedly to select “AUTO OFF”.
2 Press [R, T] to select “ON” and then press [OK].
To cancel, select “OFF”.
Note:
This function does not work when you are in radio source or
when a Bluetooth
®
device is connected.
Bluetooth
®
standby
This function automatically switches on the system when
you establish a Bluetooth
®
connection from a paired
device.
1 Press [SETUP] repeatedly to select
“BLUETOOTH STANDBY”.
2 Press [R, T] to select “ON” and then press [OK].
To cancel, select “OFF”.
Checking the software version
1 Press [SETUP] repeatedly to select “SW VER.” and
then press [OK].
The software version is shown.
2 Press [OK] again to exit.
PRESET EQ “HEAVY” (default), “SOFT”, “CLEAR”,
“VOCAL” or “FLAT”
BASS –4 to +4 (default: 0)
Using the main unit
1. Press [BASS].
2. Press [2/3] or [5/6].
TREBLE –4 to +4 (default: 0)
Using the main unit
1. Press [TREBLE].
2. Press [2/3] or [5/6].
D.BASS “ON D.BASS” (default) or “OFF D.BASS”
SURROUND “ON SURROUND” or
“OFF SURROUND” (default)
RQT0A08-B_en.fm Page 17 Thursday, March 5, 2015 9:44 AM
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

panasonic-sc-pm250b

Suche zurücksetzen

  • Panasonic SC-PM 250 Wie kann ich CD einschalten u. abspielen.Bei CD zeigt NO CD ein.
    Wie geht es. Eingereicht am 20-10-2022 11:25

    Antworten Frage melden






  • Wie programmiert man einen Sender? Ruft diesen auch auf. Wie kann man die einzelnen Sender abrufen ohne den Sender zu verstellen.



    Eingereicht am 26-2-2022 18:46

    Antworten Frage melden

  • Ich finde keine Sender über Kabelanschluss, was muss ich tun?
    Eingereicht am 17-8-2021 09:14

    Antworten Frage melden

  • Wie stelle ich genau das Dab ein, die Einleitung ist zu kurz und ungenau. Eingereicht am 12-11-2020 15:23

    Antworten Frage melden

  • nach längerer Pause,lässt sich,ausser 1 Sender nichts einstellen?
    Eingereicht am 26-9-2020 16:22

    Antworten Frage melden

  • Hallo , wie bekomme ich in meinem Radio den Sender WDR 4 in meinem Gerät " Panasonic SA - PM 250 ? Es klappte viele Jahre mit diesem Sender . Jetzt habe ich das Gerät etwas umgestellt u.ich bekomme keinen Empfang auf 10130 ?
    Mein Bedienungshandbuch ist abhanden gekommen . Können Sie mir diese Daten zur Verfügung stellen ?
    Für Ihre Bemühungen bedanke ich mich .

    Mit freundlichen Grüßen

    Claus Basse Eingereicht am 15-8-2020 14:31

    Antworten Frage melden

  • Wie kann ich die gespeicherten Radiosender aufrufen? Eingereicht am 15-5-2020 08:30

    Antworten Frage melden

  • welche knöpfe muss ich drücken, um die cd abzuspilen?
    Eingereicht am 8-11-2019 14:56

    Antworten Frage melden

  • Wo kann ich Sender wählen, die schon eingestellt sind auf der Fernbedienung

    Eingereicht am 12-10-2019 07:40

    Antworten Frage melden

  • Hörbücher hören, Stelle wiederfinden, wo man aufgehört hat Eingereicht am 1-1-2019 14:48

    Antworten Frage melden

  • Kann man Zufallswiedergabe bei Einsatz eines USB-Stick einstellen? Eingereicht am 26-7-2018 17:05

    Antworten Frage melden

  • Zu Panasonic SC-PM 250 BEG-S Micro fehlen die Größenangaben. Wie breit ist die Gesamtanlage. Eingereicht am 1-5-2018 13:49

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic SC-PM250B wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Panasonic SC-PM250B

Panasonic SC-PM250B Bedienungsanleitung - Deutsch, Holländisch, Dänisch, Französisch, Italienisch - 100 seiten

Panasonic SC-PM250B Bedienungsanleitung - Portugiesisch - 2 seiten

Panasonic SC-PM250B Bedienungsanleitung - Polnisch - 2 seiten

Panasonic SC-PM250B Bedienungsanleitung - Schwedisch, Finnisch - 100 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info