Bedienungsanleitung Panasonic SCPM91D (Seite 33 von 36) (Englisch)

618451

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

RQT7937

Troubleshooting guide

Sound

No sound.

Distorted sound.

• Check the connections. (6)

• Turn the volume up.

• Turn muting off. (26)

• Turn Advanced surround off if it causes distortion. (25)

• Switch off the unit, determine and correct the causes, then switch the unit on.

Causes include:

– Shorting (bare wires touching) of positive and negative speaker wires.

– Using speakers with an impedance lower than that rated for this unit.

– Straining of the speakers through excessive volume or power.

– Using the unit in a hot environment without proper ventilation.

Piercing noise comes from the

speakers.

• If you have connected this unit to other equipment through the OPTICAL OUT terminal, ensure you have

selected the correct settings for “Dolby Digital”, “DTS Digital Surround” and MPEG

in the Setup menus’

“Audio” tab. (21)

Picture

Picture distorted. • Some distortion is normal during search.

No picture.

• Check the connection.

• Make sure the television is on.

• Ensure the television’s video input setting (e.g., VIDEO 1) is correct.

The picture shown on the

television is not normal.

(The sides of the picture are

cut off, the picture is stretched

horizontally, or black bands

appear at the top and bottom of

the screen.)

• Go to “Video” tab in the Setup menus, and change “TV Aspect” to suit your television. (20)

• Use the television to change the aspect to the correct one.

If your television cannot change the aspect when input is progressive, try changing 4:3 Aspect in

Display Menu. (19)

• Ensure that the unit is connected directly to the television, and is not connected through a video cassette

recorder.

• Change the size with the zoom function. (19)

•

Connect to the component video (480P) input terminals on a television compatible with this unit’s copy

guard system. You cannot view progressive video if your television is not compatible. (7)

There is ghosting when

progressive output is on.

• Change “Video Output Mode” to “480I” so “PROG.” on the display goes out. This problem is caused by the

editing method or material used on DVD-Video, but should be corrected if you use interlace output. (19)

Picture quality is poor. • Check the settings in Picture Menu. (19)

The picture on the television

disappears or stripes appear on

the screen.

• Mobile telephone chargers can cause some disturbance.

• The location and orientation of the antenna are incorrect. If you are using an indoor antenna, change to an

outdoor antenna. (31)

• The television antenna wire is too close to the unit. Separate the antenna wire of the television from the

unit.

Menus not displayed correctly.

• Change the zoom ratio to “x1.00”. (19)

• Set “Subtitle Position” in Display Menu to “0”. (19)

•

Set “4:3 Aspect” in Display Menu to “Normal”. (19)

Unit displays

Although the unit is in standby

mode, the display lights up and

changes continuously.

• Turn off the demo function. (If you set the clock, the demo function turns off automatically.) (9)

The display is dark. • Press [SHIFT]+[DIMMER] until the display returns to the original brightness. (26)

“DVD NO PLAY”

• You inserted a disc which the unit cannot play; insert one that can. (4)

• You inserted a blank DVD-RAM disc.

“DVD NO DISC”

• You haven’t inserted a disc; insert one.

• You haven’t inserted the disc correctly; insert it correctly. (5, 12)

“F61”

• Check and correct the speaker cord connections. (6)

If this does not ﬁx the problem, there is a power supply problem. Consult the dealer.

“DVD U11” • Disc is dirty. Wipe it clean. (5)

“ERROR” • Incorrect operation performed. Read the instructions and try again.

“DVD H ”

stands for a number.

• Trouble may have occurred. The number following "H" depends on the status of the unit.

Reset procedure:

Press [

^] to switch the unit to standby mode and then back to ON. Alternatively, press [^] to switch the

unit to standby mode, disconnect the AC mains lead, and then reconnect it.

• If the service numbers fail to clear, note the service number and contact a qualiﬁed service person.

Television displays

“Cannot play(display) group xx,

content xx.”

• You are trying to display incompatible contents.

No on-screen display. • Go to “Display” tab in the Setup menus, and select “On” for “On-Screen Messages”. (21)

The disc’s menu is displayed in a

different language.

• Go to “Disc” tab in the Setup menus, and select the preferred language for “Menus”. (20)

(

This function is dependent on software availability.)

Except for Southeast Asia

For Australia, N.Z., the Middle East and Southeast Asia

For Australia, N.Z., the Middle East

and Southeast Asia

For Australia, N.Z., the Middle East and Southeast Asia

SC-PM91D EB.indd 33 3/18/2005 2:18:57 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCPM91D Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SCPM91D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info