745203
30
Zoom out
Zoom in
Vorherige Seite
1/33
Nächste Seite
30 GB
Q
Rotating the hand grip
DANGER OF INJURY! Pull
the mains plug out of the socket before you carry
out any task on the device. The hand grip
4
can
be rotated by 90° to the right or left. This allows
the ON / OFF switch
3
to be brought into the most
comfortable position for any working conditions.
Press the unlocking button
10
and rotate the
hand grip
4
to the right or left.
Make sure the hand grip
4
engages.
Q
Adjusting the shoe
DANGER OF INJURY! Pull
the mains plug out of the socket before you carry
out any task on the device.
Adjust the shoe
5
to suit the cutting depth.
To do this release the shoe adjustment lever
8
and place the shoe
5
in appropriate position.
Lock the shoe in this position by pulling the
shoe adjustment lever
8
tight.
Q
Setting the blade speed
With the oscillation speed setting wheel
1
you can
chose the desired stroke rate (- = lower stroke rate,
+ = higher stroke rate).
The stroke setting can also be changed during op-
eration.
Q
Preparing for use
Q
Switching on and off
When operating the device you can select between
intermittent or continuous operation mode.
To switch on intermittent operation mode:
Press the ON / OFF switch
3
.
To switch off intermittent operation mode:
Release the ON / OFF switch
3
.
To switch on continuous operation mode:
Press the ON / OFF switch
3
and fix it in the
pressed position with the lock button
2
.
To switch off continuous operation mode:
Press the ON / OFF switch
3
and release it
again.
Q
Guiding the sabre saw
safely and accurately
The shoe
5
pivots to adjust to the workpiece and
provides safe support to the device. It must always
lie against the workpiece when the device is in use.
Q
Advice about ways of
working when sawing
Before sawing, check the workpiece for foreign
bodies such as nails, screws etc. and remove
them.
Do not allow the ventilation slots to become
covered.
Switch the device on first and only then bring it
into contact with the workpiece.
If the saw blade jams, switch off the device im-
mediately.
Open the sawn gap in the workpiece slightly
using a suitable tool and extract the saw blade.
Always make sure the saw blade type and the
blade oscillation speed are suitable for the
workpiece material.
There are different saw blades available in var-
ious lengths designed to ensure optimum perfor-
mance of every sawing task with your sabre saw.
Saw the material using a steady forward rate
of progress.
Flush sawing:
Using flexible saw blades of adequate length you
can trim off projecting workpieces, such as pipes,
directly at the face of a wall.
Before use / Preparing for use Preparing for use / Maintenance and cleaning / Service centre / Warranty
30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 43001 PFS 710 B1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Parkside IAN 43001 PFS 710 B1

Parkside IAN 43001 PFS 710 B1 Bedienungsanleitung - Französisch, Italienisch - 43 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info