745200
27
Zoom out
Zoom in
Vorherige Seite
1/31
Nächste Seite
27 GB
General safety advice on power tools
5. Service
a) Only have the power tool repaired by
qualified professionals using OEM
spare parts. This ensures the safety of the
power tool is maintained.
Safety notes for hammer drills
Wear hearing protection. Exposure to
noise can cause hearing loss.
Use the additional handle when using
the device. Losing control can lead to injury.
Hold the device by the insulated han-
dles when performing work n appli-
cations where a potential danger of
the tool striking hidden electrical lines
or its own power cable. Contact with a
live wire could cause metal parts of the device
to become live and lead to electric shock.
Wear a dust mask.
TOXIC DUST! Working on
materials which can produce harmful / toxic dusts
presents a health risk to the user and people
within close vicinity.
CAUTION - LEADS! DANGER! Verify you
will not strike electric-, gas- or water lines whilst
using the power tool. If necessary, first use a
cable detector before drilling into or cutting
open a wall.
Start-up
Pivot additional handle
Note: For safety reasons this device must only be
used with the additional handle
7
installed (also
see Fig. C, D, E).
The position of the additional handle
7
can be
adjusted. Turn the wing screw
1
anti-clockwise
and swivel the additional handle
7
into the
desired position.
Then tighten the wing screw
1
again.
This unit features an LED
5
. It will light up once
the unit is connected to the mains, indicating
the unit is energised and will immediately switch
on when the ON / OFF switch
3
is activated.
Depth stop
Open the wing screw
1
.
Insert the depth stop
11
in the additional
handle
7
.
Make sure that the toothing on the depth stop
11
is pointing downwards.
Pull the depth stop
11
out as far as necessary
so that the distance between the tip of the drill
and the tip of the depth stop corresponds to
the desired drilling depth.
Firmly tighten the wing screw
1
.
Inserting / removing tools
Inserting tools:
Lightly grease the tool holder before inserting
the tool
8
.
To insert, pull back the locking sleeve
10
and
insert the tool.
Release the locking sleeve
10
. This locks the
tool holder. Pull the tool to ensure that it is firm-
ly locked in place. The tool has some radial play
inherent in the system.
Removing tools:
To remove the tool pull back on the locking
sleeve
10
.
Quick-release chuck for
round shaft drills
Do not use the quick-release
chuck for round shaft drills for hammer drilling or
chiseling applications!
Set the function selector switch
6
to the drill
symbol
.
General safety advice on power tools / Start-up
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 46883 PBH 1050 A1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Parkside IAN 46883 PBH 1050 A1

Parkside IAN 46883 PBH 1050 A1 Bedienungsanleitung - Französisch - 33 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info