744954
34
Zoom out
Zoom in
Vorherige Seite
1/37
Nächste Seite
34 GB
detailed image in Fig. C. Ensure that the nail
heads are all at the top.
NOTE: Observe the maximum capacity of ap-
prox. 85 staples or approx. 75 nails when filling.
After filling, push the magazine slider
4
into
the magazine
5
as far as it will go until you
hear and feel it engage.
NOTE: The magazine filling level indicator
6
allows you to see whether there are still staples
in the magazine.
Q
Setting the impact force
NOTE: Select the lowest impact force necessary
for your stapling.
Take into account the length of the staples or nails
to be used and the strength of the materials to be
joined.
Impact force controller
3
Increase impact force:
Turn the impact force controller
3
anticlockwise.
Decrease impact force:
Turn the impact force controller
3
clockwise.
Q
Use
Q
Switching on and off
Set the ON / OFF switch
2
to position “I” to
switch on the device.
Set the ON / OFF switch
2
to position “0” to
switch off the device.
Q
Stapling / nailing
Switch the device on by setting the ON / OFF
switch
2
to position “I”.
Press the device with its front plate
7
at the
point on the surface of the material where you
wish to staple or nail.
Press the trigger
1
.
NOTE: The integral safety lock in the front
plate prevents unintentional firing.
Q
Troubleshooting
Cause:
A staple or nail is blocking the device.
Solution:
Open the magazine slider
4
. This releases
the pretension. Release the screws on the front
plate
7
using the Allen key (Fig. D).
Remove the staple or nail.
Q
Maintenance and cleaning
DANGER OF INJURY! Pull
the mains plug out of the mains socket before you
clean or maintain the device.
The electric nailer / stapler is designed to be main-
tenance-free.
Always keep the device clean, dry and free
from oil or grease.
Clean the device immediately after you have
finished using it.
Do not allow any liquids to enter the device.
Use a cloth to clean the housing. Never use
petrol, solvents or cleaning agents that might
attack plastic.
Q
Service
Have your device
repaired at the service centre or by
qualified specialist personnel using
original manufacturer parts only. This
will ensure that your device remains safe to use.
If the plug or lead
needs to be replaced, always have
the replacement carried out by the
manufacturer or its service centre. This
will ensure that your device remains safe to use.
Warranty / DisposalBefore use / Use / Maintenance and cleaning / Service
34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 71828 PET 25 A1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info