Bedienungsanleitung Parkside IAN 73782 PDT 40 B2 (Seite 34 von 37) (Deutsch, Englisch, Holländisch, Französisch)

745069

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

34 GB

Maintenance and cleaning / Service / Warranty / DisposalOperation / Maintenance and cleaning

provide any performance increase, but only in-

creases compressed air consumption and ac-

celerates wear on the device.

Switch on the compressor.

Allow the compressor to run once long enough

until maximum tank pressure is reached and the

device is switched oﬀ.

Place the compressed air tacker on the workpiece

and press the trigger

NOTE: The compressed air tacker

is equipped with a trigger lock

The fastener will only leave the device

when the mouth of the compressed air tacker is

pressed against the workpiece and the trigger

is actuated.

Check that the fastener has been driven in cor-

responding to the work requirements.

– If the fastener is protruding, increase the air

pressure in 0.5 bar increments.

– If the fastener is too deep, decrease the air

pressure in 0.5 bar increments.

As an alternative, you can accelerate the work

by keeping the trigger

depressed.

Set the compressed air tacker against the work-

piece.

Press the device against the workpiece until the

mouth

touches it. The fastener will leave the

device.

As long as the trigger

is kept depressed, each

time the mouth

touches the workpiece one

fastener will leave the device.

Another alternative is to keep the mouth

pressed against the workpiece.

Each time the trigger

is actuated, a fastener

will leave the device.

NOTE: Fine adjustment with the knurled screw

is possible.

Turn the knurled screw

downwards in order

to drive the fastener more deeply into the work-

piece.

Turn the knurled screw

upwards in order to

drive the fastener less deeply into the workpiece.

Turn the exhaust air aperture

to guide the

exhaust airﬂow in the desired direction.

After ﬁnishing work, disconnect the device from

the compressor.

Removing jammed fasteners

If a staple or nail gets jammed in the magazine

slot, immediately disconnect the compressed

air supply.

Open the magazine

as described in the

chapter “Loading the magazine“.

Open the face plate

by pulling the face

plate quick clamping lever

in the direction

of the trigger lock

Remove the jammed fastener.

Close the face plate

by pulling the face

plate quick clamping lever

in the direction

of the exhaust air aperture

Close the magazine

of the compressed air

tacker as described in the chapter “Loading the

magazine“.

Maintenance and cleaning

RISK OF INJURY! Be absolutely certain to

disconnect the device from the compressed air

source before cleaning or maintaining it.

Maintenance

Lubrication with oil mister

NOTE: As a treatment stage after the pressure re-

ducer, an oil mister provides continuous and opti

mum

lubrication of the compressed air tacker. An oil mis-

ter gives oﬀ ﬁne drops of oil into the airﬂow and so

guarantees regular lubrication.

Install the oil mister after the (ﬁlter) pressure re-

ducer. To do so, insert the nipple of the oil mis-

ter into the quick-release coupling of the (ﬁlter)

pressure reducer.

Then connect the compressed air device to the

quick-release coupling provided for it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 73782 PDT 40 B2 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info