Bedienungsanleitung Parkside IAN 75636 PABS 18 Li B2 (Seite 49 von 52) (Deutsch, Englisch, Holländisch, Französisch)

744943

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

49 GB

Preparing the tool for use / Cleaning and Maintenance / Service / WarrantyBefore first use / Preparing the tool for use

Soft screwdriving conditions (e.g. into

soft wood):

You should also select a low speed in order not to

damage the wood workpiece surface through con-

tact with the metal screw head. Use a countersinker.

When drilling into wood, metal and other

materials, take note of the following advice:

With small diameter drill bits use a high drill

speed. For large diameter drill bits, use a low

drill speed.

For hard materials, select a low drill speed.

For soft materials, select a high drill speed.

Secure or ﬁx down the workpiece (if possible)

in a clamp or vice.

Mark the intended position of the hole with a

centre punch or a nail and select a low drill speed

for drilling.

Take the rotating drill bit out of the hole frequently

so that swarf or drill dust can be re-moved and

the hole and tool is ventilated.

Drilling in metal:

Use a metal drill bit (HSS). For the best results,

you should cool the bit with oil. Metal drill bits

can also be used to drill into plastic.

Drilling in stone:

Use a circular shafted masonry drill bit with a

hardened metal tip.

Drilling in wood:

Normally you should use a wood drill with a

centring point. For deep holes, use an auger type

bit. For large diameter holes, use a forstner bit.

You can screw small screws into soft wood

without the need for pre-drilling.

Cleaning and Maintenance

CAUTION! Place the direction of rotation

switch

into the middle position before carry-

ing out any tasks on the device, e.g. changing

tools or maintenance, or before transporting or

storing the device. Inadvertent operation of the

ON / OFF switch

may result in injury.

Pull the mains lead out of the mains socket eve-

ry time and remove the battery before you clean

or maintain the device.

The Cordless drill is maintenance-free.

Always keep the device clean, dry and free of

oil or grease.

Clean the device immediately after you have

ﬁnished using it.

Do not allow any liquids to enter the device.

Use a cloth to clean the housing. Never use

petrol, solvents or cleaning agents that might

attack plastic.

Service

Have your device repaired

at the service centre or by qualified

specialist personnel using original

manufacturer parts only. This will ensure

that your device remains safe to use.

If the plug or lead needs

to be replaced, always have the

replacement carried out by the manu-

facturer or its service centre. This will

ensure that your device remains safe to use.

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 75636 PABS 18 Li B2 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info