745078
40
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
40 GB
OperationGeneral safety advice for electrical power tools / Operation
Never support your hands next to or
in front of the device or on the surface
being worked as there is a risk of in-
jury in the event of slipping.
Always switch off the appliance and
allow the sanding sheet
9
to come to
a stop before setting down the oscil-
lating sander.
Always pull the power plug out of the
socket for all work pauses, before any
work on the appliance (e.g. changing
the sanding paper) and when not in
use.
The appliance must always be kept
clean, dry and free of oil or lubricat-
ing greases.
Original ancillaries / and
accessories
Only use accessories and tools that
are specified in the operating instruc-
tions. The use of tools and accessories other
than those recommended in the operating in-
structions could lead to an increased risk of
personal injury for you.
Operation
Switching On and Off
Switching on intermittent function:
Press the ON / OFF switch
1
.
Switching off intermittent function:
Release the ON / OFF switch
1
.
Switching on continuous operation :
Press the ON / OFF switch
1
, hold it pressed
and press the locking button
2
.
Switching off continuous operation:
Press the ON / OFF switch
1
then release it
again.
Setting the oscillation speed
You can set the desired oscillation speed as needed
with the oscillation speed selector
10
.
The required oscillation speed depends on the ma-
terial being worked and can be determined through
practical tests.
Attaching a sanding sheet
Before performing work on the
appliance, always disconnect the power.
NOTE: Before attaching a new sanding sheet
9
,
remove dust and dirt from the sanding plate
8
.
Sanding sheets with hook and loop
fastening:
Fix one side of the sanding sheet
9
flush with
one side of the backing plate
8
.
Then attach the sanding sheet
9
to the back-
ing plate
8
and press it firmly into place.
Sanding sheets without hook and loop
fastening:
Open the two clamping levers
7
.
Push one end of the sanding sheet
9
under
the open clamping bar
6
and clamp the
sheet firmly in place by locking the clamping
lever
7
back in place.
Repeat this procedure at the other end.
Various materials require different grit values. You
can read which grit value is best suited for which
work in our recommendations under “Instructions,
tips and tricks”.
Vacuuming dust
FIRE HAZARD!
A risk of fire exists when working with
electrical appliances that have a dust
collection box
4
or can be attached to a vacuum
cleaner via an external suction adapter! Under cer-
tain conditions the sanding dust in the dust box (or
in the vacuum’s dust bag) may self-ignite, e.g. as a
result of flying sparks generated when abrading
40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 75912 PSS 250 A1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info