Bedienungsanleitung Parkside IAN 85969 PFS 710 A1 (Seite 31 von 34) (Deutsch, Englisch, Holländisch)

745118

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

31 GB

To switch oﬀ continuous operation mode:

j Press the ON / OFF switch

and release it

again.

Guiding the sabre saw

safely and accurately

The shoe

pivots to adjust to the workpiece and

provides safe support to the device. It must always

lie against the workpiece when the device is in use.

Advice about ways of

working when sawing

J Before sawing, check the workpiece for foreign

bodies such as nails, screws etc. and remove

them.

J Do not allow the ventilation slots to become

covered.

J Switch the device on ﬁrst and only then bring it

into contact with the workpiece.

J If the saw blade jams, switch oﬀ the device im-

mediately.

Open the sawn gap in the workpiece slightly

using a suitable tool and extract the saw blade.

j Always make sure the saw blade type and the

blade oscillation speed are suitable for the

workpiece material.

j There are diﬀerent saw blades available in var-

ious lengths designed to ensure optimum perfor-

mance of every sawing task with your sabre saw.

j Saw the material using a steady forward rate

of progress.

Flush sawing:

Using ﬂexible saw blades of adequate length you

can trim oﬀ projecting workpieces, such as pipes,

directly at the face of a wall.

Follow these steps:

1. Place the saw blade directly on the wall surface.

2. Bend the blade by applying sideways pressure

so that the shoe

comes up against the wall.

3. Switch on the device as described above and

trim the workpiece using constant pressure.

Plunge sawing:

CAUTION! DANGER OF KICKBACK!

Plunge sawing can be used only in soft materials

(such as wood etc.).

Follow these steps:

1. Place the sabre saw with the underside of the

shoe

against the workpiece.

Switch on the device.

2. Tilt the sabre saw forward and plunge the saw

blade into the workpiece.

3. Bring the sabre saw vertical and continue saw-

ing along the cutting line.

Note: The saw blade used for this should not be

longer than 152 mm!

Maintenance and cleaning

J Pull the mains lead out of the mains socket

before you clean the device.

J Replace the saw blade as soon as its teeth be-

come blunt and it starts to produce defective

saw cuts.

J Always keep the device and the ventilation

slots clean.

j Clean the device after you have ﬁnished using it.

j Do not allow any liquids to enter the device.

Use a cloth to clean the housing. Never use

petrol, solvents or cleaning agents that might

attack plastic.

If necessary, clean out the

saw blade mounting recess

with a thin paintbrush or compressed air.

Service centre

Have your device

repaired only by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

If the plug or mains

lead needs to be replaced, always

have the replacement carried out by

the manufacturer or its service centre.

General safety advice for electrical power tools / Before use / Preparing for use Preparing for use / Maintenance and cleaning / Service centre

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 85969 PFS 710 A1 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 85969 PFS 710 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info