Bedienungsanleitung Parkside IAN 90877 PABS 18 Li B3 (Seite 30 von 34) (Deutsch, Englisch, Holländisch)

745080

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

30 GB

in the middle position (lock). To prevent

the device from starting up unintentionally.

DANGER! Take steps to ensure that

you do not hit upon any service lines

(electricity, gas, water) when work-

ing with electrical appliances. Check, if

need be with a service line detector, before

you start to cut or bore into a surface.

Original ancillaries /

accessories

Use only the ancillaries and accessories

that are detailed in the operating

instructions. The use of ancillaries and ac-

cessories other than those recommended in the

operating instructions could lead to an increased

risk of personal injury for you.

Start-up

Charging the battery pack

CAUTION! Always ensure the plug is removed

from the mains socket before inserting a battery pack

into, or removing one from, the charging station.

Never charge the battery pack if the ambient

temperature is less than 10 °C or greater than

40 °C.

1. Insert the battery pack

into the quick-

charger

(see Fig. C).

2. Insert the mains plug into the mains socket. The

ﬂashing green charge indicator LED

shows

that charging is in progress.

3. The charging process is completed when the

green charge indicator LED

light up and the

accumulator pack

is ready for operation.

4. If the red charge indicator LED

lights up, the

quick battery charger

is in standby mode;

the accumulator pack

is not connected.

5. If the red charge indicator LED

starts ﬂas-

hing, this means that the accumulator pack

has become too hot; no charging process.

Never charge the battery pack for a second time

immediately after a fast charging process has

been completed. This can give rise to the battery

pack becoming overcharged and to a reduced

service life of the battery and charging station.

Switch the charger oﬀ for at least 15 minutes

between two successive charging procedures.

Remove the power plug from the wall socket.

Insertion / removal of a battery

pack into the appliance

Inserting the rechargeable battery pack:

Move the rotation switch

into the middle

position (lock). Push the rechargeable battery

pack

into the handle until it engages.

Removing the rechargeable battery pack:

Press the release button

and remove the

rechargeable battery pack

Checking battery status

To check the battery status, press the battery

LED button

(refer to main diagram).

The three battery LEDs

indicate the condition

and the remaining charge as follows:

GREEN / RED / ORANGE = maximum charge /

capacity

RED / ORANGE = medium charge / capacity

RED = weak charge – recharge battery

Changing tools

Your cordless drill has a fully automatic spindle

lock

Once the motor has come to a halt, the drive shaft

is automatically locked, so that the chuck

can

be opened simply by turning it

After you have inserted the required bit and ﬁxed it

in place by turning the chuck

, you can immedi-

ately continue working. The spindle lock releases

itself automatically when the motor is started (by

operation of the ON / OFF switch

Start-up / OperationGeneral safety advice for electrical power tools / Start-up

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 90877 PABS 18 Li B3 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 90877 PABS 18 Li B3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info