Bedienungsanleitung Parkside IAN 97735 PFS 100 C2 (Seite 30 von 33) (Deutsch, Englisch, Holländisch)

745206

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

30 GB

Maintenance and cleaning / Service centre / Warranty / DisposalAdvice on use / Bringing into use / Maintenance and cleaning

* This device cannot be used to spray media contain-

ing discrete particles / solids. The abrasive eﬀect

of these media shortens pump and valve life.

Preparing the surface

to be sprayed

The surface to be sprayed must be clean, dry and

free of grease.

Roughen smooth surfaces and remove any

abraded dust.

Always cover the surrounding area around the

surface to be sprayed. The spray cloud may

contaminate the surrounding area.

Bringing into use

Selecting the nozzle

Nozzle Use

Nozzle, 0.6 mm

(R6)

all paints, varnishes

Nozzle, 0.8 mm

(R8)

thick-ﬂowing sprayed media

Cleaning nozzle

a thinner, harder spray for

spot-cleaning of surfaces

Nozzle extension

for spraying into corners

which are diﬃcult to reach

Switching ON / OFF

Switching on:

To start the electrical power tool, press the

ON / OFF switch

and keep it pressed.

Switching off:

To switch oﬀ the electrical power tool, release

the ON / OFF switch

Spraying process

1. You can vary the spray by adjusting the regulator

button

(see Fig. D). The spray is correctly

set when no drops are formed and the gun

produces a ﬁne, consistent spray pattern.

2. Do not switch the device on or oﬀ while it is

over the surface to be sprayed. Instead, start

and stop the spraying process approximately

10 cm outside the surface to be sprayed.

NOTE: The distance between the nozzle and

the workpiece depends on the material being

sprayed (approx. 20 to 35 cm spraying dis-

tance, depending on the spray cone and the

desired amount of material to be applied).

Use the device in a horizontal orientation only

(as shown in Fig. D).

Carry out a trial in each case to determine the

most eﬀective spraying distance.

Start with a longer distance.

3. Spray corners or small decorative details ﬁrst

using short bursts of spray.

Then go on to the actual spraying process.

4. The spray process should follow the sequence

shown in Fig. E

– keep the spray gun moving parallel to the surface

– Do not incline the spray gun

– Move the spray gun at a constant speed

– Apply the sprayed medium as thinly as possible

– The layer(s) of sprayed medium need(s) to

be allowed to dry for some time before you

apply the next coat (Fig. F) at right angles to

the previous coat.

5. Do not allow the paint cup

to empty com-

pletely while spraying – drops may form!

Maintenance and cleaning

General advice:

Pull out the mains plug be-

fore you carry out any tasks on the spray gun.

Do the same when you take a break from spraying.

2. After each use, spray thinners (in the open

air only – danger of explosion!) or

water through the device.

3. To protect from rust after cleaning, you can

spray sewing machine oil through the device.

DANGER TO LIFE

THROUGH ELECTRIC SHOCK! Never im-

merse the device in the cleaning medium.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 97735 PFS 100 C2 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 97735 PFS 100 C2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info