679211
7
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
7 GB/IE
Introduction / General power tool safety warnings
1 Quick-release chuck with SDS-plus bit system
(see Fig. A)
3 Drill bits (Ø 6 / 8 / 10 mm x 150 mm) (see Fig. B)
1 Flat chisel 250 mm (see Fig. B)
1 Pointed chisel 250 mm (see Fig. B)
1 Depth stop
50 g Special grease for lubricating the chuck
1 Carrying case
1 Set of instructions for use
Technical Data
Rated input: 1050 W
Rated voltage: 230 V∼, 50 Hz
Idle speed: n
0
0–980 rpm
BPM: 0–5300 rpm
Impact energy: 3 joules
Max. bore diameter: max. 13 mm in steel
max. 32 mm in wood
max. 26 mm in concrete
Protection class: II /
Noise emission value:
Measured sound value determined according to
EN 60745. The A-rated noise levels of the electrical
power tool are typically at:
Hammer drilling:
Sound pressure level: L
: 83.66 dB(A)
Uncertainty K: 3 dB(A)
Sound power level: L
: 94.66 dB(A)
Uncertainty K: 3 dB(A)
Chiselling:
Sound pressure level: L
: 90.62 dB(A)
Uncertainty K: 3 dB(A)
Sound power level: L
: 101.62 dB(A)
Uncertainty K: 3 dB(A)
Wear hearing protection!
Vibration total value:
The total vibration (vector sum of three directions) is
calculated in accordance with EN 60745:
Hammer drilling
into Concrete: a
h(HD)
= 8.527 m / s
2
,
K = 1.5 m / s
2
Chiselling: a
h(CHeq)
= 11.293 m / s
2
,
K = 1.5 m / s
2
The vibration level specified in
these instructions was measured in accordance with
an EN 60745 standardised measurement process
and can be used to compare equipment. The vibra-
tion emission value specified can also serve as a
preliminary assessment of the exposure.
The vibrati
on level may change with the application
of the tool and in some cases may be higher than
the value specified in these instructions. Regularly
using the electric tool in such a way may make it
easy to underestimate the vibration.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particu-
lar period of work, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can clearly reduce the vibration load through-
out the work period.
General power tool
safety warnings
Read all safety
warnings and all instructions.
Failure to follow the warnings and in-
structions may result in electric shock, fire and / or
serious injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-op-
erated (cordless) power tool.
Introduction
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PBH 1050 B2 - IAN 273100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info