Bedienungsanleitung Parkside PBH 1050 B2 - IAN 273100 (Seite 9 von 44) (Deutsch, Englisch, Holländisch, Französisch)

679211

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

9 GB/IE

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch is

dangerous and must be repaired.

c) Pull the mains plug out of the socket

and / or remove the rechargeable bat-

tery before you make any adjustments

to the device, change accessories or

when the device is put away. This pre-

caution is intended to prevent the device from

unintentionally starting.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of un-

trained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other con-

dition that may affect the power tool’s

operation. If damaged, have the power

tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations diﬀerent from those intended could

result in a hazardous situation.

5. Service

a) Have your power tool serviced by a

qualified repair person using only

iden-

tical replacement parts. This will ensure

that the safety of the power tool is maintained.

Safety notes for hammer drills

Wear hearing protection!

Exposure to noise can cause hear-

ing loss.

Use the additional handle when using

the device. Losing control can lead to injury.

Hold the device by the insulated han-

dles when performing work n appli-

cations where a potential danger of

the tool striking hidden electrical lines

or its own power cable. Contact with a

live wire could cause metal parts of the device

to become live and lead to electric shock.

Wear a dust mask!

TOXIC DUST! Working on

materials which can produce harmful / toxic dusts

presents a health risk to the user and people

within close vicinity.

CAUTION - LEADS! DANGER! Verify you will

not strike electric-, gas- or water lines whilst using

the power tool. If necessary, ﬁrst use a cable de

tector before drilling into or cutting open a wall.

Start-up

Pivot additional handle

Note: For safety reasons this device must only be

used with the additional handle

installed (also

see Fig. C, D, E).

The position of the additional handle

can be

adjusted. Turn the wing screw

anti-clockwise

and swivel the additional handle

into the

desired position.

Then tighten the wing screw

again.

This unit features an LED

. It lights up red after

connecting the device to the mains. This indicates

the device is energised and will start immediate-

ly when pressing the ON / OFF switch

General power tool safety warnings / Start-upGeneral power tool safety warnings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PBH 1050 B2 - IAN 273100 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info