679211
10
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
10 GB/IE
Start-up / Maintenance and Cleaning / Service / WarrantyStart-up
Depth stop
Open the wing screw
1
.
Insert the depth stop
11
in the additional
handle
7
.
Make sure that the toothing on the depth stop
11
is pointing downwards.
Pull the depth stop
11
out as far as necessary
so that the distance between the tip of the drill
and the tip of the depth stop corresponds to
the desired drilling depth.
Firmly tighten the wing screw
1
.
Inserting / removing tools
Inserting tools:
Lightly grease the tool holder
8
before insert-
ing the tool.
To insert, pull back the locking sleeve
10
and
insert the tool.
Release the locking sleeve
10
. This locks the
tool holder. Pull the tool to ensure that it is firm-
ly locked in place. The tool has some radial play
inherent in the system.
Removing tools:
To remove the tool pull back on the locking
sleeve
10
.
Quick-release chuck for
round shaft drills
Do not use the quick-release
chuck for round shaft drills for hammer drilling or
chiseling applications!
Set the function selector switch
6
to the drill
symbol
.
Attaching the quick-release chuck for
round shaft drills:
To attach the additional chuck for round shaft
drills (also see Fig. A) pull back the locking
sleeve
10
and insert the additional chuck.
Release the locking sleeve
10
. This locks the tool
holder. Pull the tool to ensure that it is firmly
locked in place.
Removing the quick-release chuck for
round-shaft drills:
To remove the additional chuck pull back the lock-
ing sleeve
10
and remove the additional chuck.
Inserting tools:
RISK OF INJURY! Switch the
device off and unplug from the mains socket before
performing any work on the device.
Setting the function with the
function selector switch
Press and hold the release button for the function
selector switch
6 a
and turn the function selector
switch
6
until the desired symbol locks in next
to the arrow.
The functions are marked as follows:
Function Symbol
Drilling / screwing
Hammer drilling
Chiseling
Chisel position
adjustment
Adjusting the chisel position:
This function allows you to turn the tool to the nec-
essary position for chiseling (also see Fig. C, D).
Turn the function selector switch
6
to position
.
Turn the tool inside the tool holder
8
to the
necessary position.
To chisel, turn the function selector switch
6
to .
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PBH 1050 B2 - IAN 273100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info