595429
24
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
21
PBH 1500 A1
GB
Appliance-specifi c safety instructions
for hammer drills
Wear ear protectors. Exposure to
noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping surfac-
es, when performing an operation where the
cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting
a “live” wire may make exposed metal parts of
the power tool “live” and could give the opera-
tor an electric shock.
Wear a dust mask.
WARNING! TOXIC DUST!
Working with harmful/toxic dusts results in
health hazards for the person operating the
appliance and for other persons in the area.
ATTENTION – SERVICE LINES! DANGER!
Take steps to ensure that you do not hit any
service lines (electricity, gas, water) when
working with the electric tool. If necessary,
check with a service line detector before you
start to cut or drill into a surface.
Original accessories/additional
equipment
Only use the accessories and additional
equipment that are specifi ed in the operat-
ing instructions and are compatible with the
appliance.
Initial operation
Additional handle
NOTE
For safety reasons, you should only use this
appliance with the additional handle
attached.
Remove the additional handle by turning it
clockwise direction.
Turn the additional handle to the desired
position.
Fix the additional handle in the new position
by turning it anti- clockwise.
Depth stop
Open the wing screw .
Insert the depth stop into the additional
handle
.
Ensure that the toothing on the depth stop is
facing upwards.
Pull the depth stop out far enough for the
distance between the tip of the drill and the tip
of the depth stop to correspond with the
required drilling depth.
Re-tighten the wing screw afterwards.
Tool/chuck:
Pull the locking sleeve backwards and insert
the tool/chuck in the tool holder .
Release the locking sleeve . This locks the
holder. Check that the tool is properly locked by
pulling it. The system has radial play because of
the design.
Removing tool/chuck:
Pull the locking collar on the tool backwards.
NOTE
Tighten the drill in the wheel-rim chuck at the
same time. To do this, apply the chuck key to all
the 3 positions on the wheel-rim chuck and
tighten the tool (e.g. drill) at the same time.
WARNING!
Do not use the wheel-rim chuck for ham-
mer drilling or chiselling!
IB_35391_PBH1500A1_LB1.indb 21IB_35391_PBH1500A1_LB1.indb 21 28.05.14 16:3528.05.14 16:35
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PBH 1500 A1 - IAN 35391 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Parkside PBH 1500 A1 - IAN 35391

Parkside PBH 1500 A1 - IAN 35391 Bedienungsanleitung - Französisch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info