595411
30
Zoom out
Zoom in
Vorherige Seite
1/34
Nächste Seite
27
PDMS A1
GB
Initial operation
NOTE
The grinder may only be operated on
cleaned, oil-atomised compressed air and
may not exceed the maximum operating
pressure of 6.3 bar at the appliance. The
compressor must be fi tted with a pressure
reducer to regulate the working pressure.
Wind the Tefl on tape supplied around all
threaded connectors.
Connect the appliance to a suitable compressed
air source.
First screw the 1/4“ threaded nipple onto
the mini compressed air oiler 1/4“ threaded
connector .
Then fi ll the mini compressed air oiler with
1-2 drops of special compressed air oil. To
do this, undo the crosshead screw at the mini
compressed air oiler
oil fi ller opening
and allow a few drops of oil to enter the oil
ller opening with the help of the oil bottle
included in delivery.
NOTE
A mist oiler continuously and optimally lubri-
cates the grinder as a preparation stage
after the pressure reducer. A mist oiler adds
ne drops of oil to air fl owing through the
appliance and therefore guarantees regular
lubrication.
Now screw the 1/4“ threaded nipple onto
the mini compressed air oiler 1/4“ female
threaded connector .
Now press the quick connector on the compressed
air hose (not included in delivery) onto the Com-
pressed air connector plug . The connection
locks automatically.
Now connect the other end of the compressed
air hose to the (fi lter) pressure reducer on the
compressor.
Tool-changing
Always disconnect the grinder from the compressed
air supply before changing tools.
Only ever use tools which are ready for use.
Furthermore, you must ensure that the minimum
clamping length of the shaft in the chuck is not
fallen below.
Using the spanners included in the accessories,
hold the spindle and chuck rmly and open
or close the chuck in the direction of the
arrows (see Fig. 3).
Fig. 3
Now insert one of the 10 diff erent whetstones .
NOTE
Please note the danger caused by mismatching
the diameter of the grinding tool shaft and
the chuck. Incorrectly-fi xed grinding tools can
cause severe vibration - injury hazard!
Ensure that the grinding tool is correctly fi xed,
and carry out a trial run of 30 seconds in a
safe area at idling speed.
OPEN
CLOSE
IB_43105_PDMSA1_LB2.indb 27IB_43105_PDMSA1_LB2.indb 27 14.05.14 11:1614.05.14 11:16
30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PDMS A1 - IAN 43105 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Parkside PDMS A1 - IAN 43105

Parkside PDMS A1 - IAN 43105 Bedienungsanleitung - Deutsch, Englisch, Holländisch - 34 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info