Bedienungsanleitung Parkside PFS 400 A1 - IAN 307721 (Seite 6 von 38) (Englisch)

679220

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

PFS 400 A1

│

3 ■

WARNING!

► The vibration level speciﬁed in these instruc-

tions has been measured in accordance with

the standardised measuring procedure spec-

iﬁed in EN 60745 and can be used to make

equipment comparisons. The vibration level

varies depending on the use of the power tool

and may be higher than the value speciﬁed in

these instructions in some cases. Regular use

of the power tool in such a way may cause

the user to underestimate the vibration.

NOTE

►

For an accurate estimate of the vibration load

during a speciﬁc working period, the periods

during which the appliance is switched oﬀ or

is running but not actually being used must

also be taken into consideration. This can

signiﬁcantly reduce the vibration load over the

total working period.

► Try to keep the vibration loads as low as

possible. Measures to reduce the vibration

load are, e.g. wearing gloves and limiting the

working time. Wherein all states of operation

must be included (e.g. times when the power

tool is switched oﬀ and times where the power

tool is switched on but running without load).

General power tool

safety warnings

WARNING!

► Read all safety warnings and all instruc-

tions. Failure to follow the warnings and

instructions may result in electric shock, ﬁre

and/or serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-op-

erated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or ground-

ed surfaces, such as pipes, radiators, ranges

and refrigerators. There is an increased risk of

electric shock if your body is earthed or ground-

ed.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entan-

gled cords increase the risk of electric shock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PFS 400 A1 - IAN 307721 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PFS 400 A1 - IAN 307721

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info