Bedienungsanleitung Parkside PSBM 500 - KH 3035 (Seite 9 von 13) (Englisch)

558819

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

10 GB/IE/CY

J If the inserted tool jams, switch off the

electrical power tool immediately. Be

prepared for high reaction torques as they may

cause kickback.

J Always keep the device clean, dry

and free of oil or grease.

J Only handle the electrical tool by

means

of the insulated handling surfaces

when

you are carrying out jobs where the

insertion tool may come into contact

with hidden power supply lines or its

own power cable. Contact with a live elec-

trical wire also makes metal parts of the electrical

tool live and leads to electric shock.

J Keep your workplace clean and tidy.

Mixing materials is particularly dangerous.

Dust from light metals can burn or explode.

J Wait until the electrical tool has come

to a standstill before putting it down.

The insertion tool could get caught up in some-

thing and this may lead to control of the electrical

tool being lost.

Caution utility services!

DANGER! Ensure that you do not strike

electrical cables, gas or water pipes when

you are working with the electrical power

tool. Check a wall using a suitable detector before

you drill or cut slots.

Original accessories /

attachments

Use only the accessories and attachments

detailed in the operating instructions.

The use of inserted tools or accessories other than

those recommended in the operating instructions

could lead to you suﬀering an injury.

Before ﬁrst use

WARNING!

DANGER OF INJURY! Switch

the device oﬀ and pull the plug out of the mains

socket before carrying out any work on the device.

Attaching the auxiliary handle

NOTE: For safety reasons this tool must always be

used with the auxiliary handle

in place.

j Turn the wing screw

anti-clockwise and

swivel the additional handle

into the de-

sired position.

j Then tighten the wing screw

again.

Using the depth stop

j Open the wing screw

j Make sure that the toothing on the depth stop

is pointing downwards.

j Pull the depth stop

out as far as necessary

so that the distance between the tip of the drill

and the tip of the depth stop corresponds to

the desired drilling depth.

j Firmly tighten the wing screw

Inserting tools

Quick-action drill chuck:

j Take ﬁrm hold of the back casing

of the

quick-action drill chuck

and turn the front

casing

until the tool can be inserted.

j Insert the tool.

j Take ﬁrm hold of the back casing

of the

quick-action drill chuck

and turn the front

casing

ﬁrmly shut.

Assembly tools for screws and nuts:

j When using screwdriver bits, always use a

universal bit holder.

j To screw things in, always switch the changeover

switch “drill / percussion drill”

to the right to

position

First use

The mains voltage at the mains socket must match

that shown on the rating plate on the device. Devic-

es marked with 230 V can also be operated at 220 V.

General safety advice for electrical power tools / Before ﬁrst use / First use

35321_IMPACT DRILL_Content_LB6.indd 10 03.09.09 12:03

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PSBM 500 - KH 3035 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PSBM 500 - KH 3035

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info