595357
11
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
11
GB IE
5. Drill the hole until the depth stop
(2) comes in contact with the
component part.
Inserting/replacing the tool
1. Open the keyless chuck (4) wide
(RELEASE) so that the tool can
be inserted. To do so, rmly hold
the rear sleeve (4a) of the keyless
chuck (4) and turn the front sleeve
(4b) in the anti-clockwise direc-
tion.
2. Insert the tool as far as possible
into the keyless chuck (4).
3. Close the keyless chuck (4) (GRIP)
in order to clamp the tool. To do
so, rmly hold the rear sleeve
(4a) of the keyless chuck (4) and
turn the front sleeve (4b) in the
clockwise direction.
4. To remove the tool again, rotate
the keyless chuck (4) and pull out
the tool.
Always use a universal bit holder
use using a screwdriver bits.
Operation
Do not use the device with-
out the additional handle. It
provides additional hold and
reduces the risk of injury.
Observe noise control and local
regulations.
Switching on and off
1. Connect the machine to the pow-
er supply.
Make sure that the net voltage
matches the voltage rating indi-
cated on the device’s type plate.
2. Switching on: Press the on/off
switch (8).
3. By using the on/off switch (8)
you can progressively control the
speed.
Gentle pressure: low speed
Increase pressure: higher speed.
4. Continuous operation: Press the
lock button (9). The on/off switch
(8) is locked.
5. Switching off: Release the on/off
switch (8).
For continuous operation, briey
press the on/off switch (8).
Pre-select speed
You can pre-select the maximum speed on
the speed adjusting ring. The on/off switch
can only be pressed up to the specied
speed.
1. Wait for the device to shut-down.
2. Set the desired speed
on the speed adjusting
ring (7).
Set the direction of rotation
The device’s direction of rotation can be
changed with the rotational direction
switch.
1. Wait for the device to shut-down.
2. Push the rotational direction
speed (6) into the desired posi-
tion:
Clockwise rotation: to drill
and screw in screws.
Anticlockwise rotation: to
loosen screws.
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PSBM 500 B3 - IAN 102531 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info