Bedienungsanleitung Parkside PZKS 1500 B2 - IAN 295934 (Seite 107 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

706364

107

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

102

GB / IE / NI

Carbon brush inspection

Check the carbon brushes after the first 50

operating hours with a new machine, or

when new brushes have been fitted. After

carrying out the first check, repeat the check

every 10 operating hours.

If the carbon is worn to a length of 6 mm,

or if the spring or contact wire are burned

or damaged, it is necessary to replace both

brushes. If the brushes are found to be

usable following removal, it is possible to

reinstall them.

11. Storage

Store the device and its accessories in

a dark, dry and frost-proof place that is

inaccessible to children. The optimum

storage temperature is between 5 and 30°C.

Store the electrical tool in its original

packaging.

Cover the electrical tool in order to protect it

from dust and moisture.

Store the operating manual with the electrical

tool.

12. Electrical connection

The electrical motor installed is connected

and ready for operation. The connection

complies with the applicable VDE and DIN

provisions.

The customer‘s mains connection as well as

the extension cable used must also comply

with these regulations.

• The product meets the requirements of

EN 61000-3-3 and is subject to special

connection conditions. This means that

use of the product at any freely selectable

connection point is not allowed.

• Given unfavorable conditions in the

power supply the product can cause the

voltage to fluctuate temporarily.

• The product is exclusively intended for

use at connection points that have a

continuous current-carrying capacity of at

least 100 A per phase.

• As the user, you are required to ensure,

in consultation with your electric power

company if necessary, that the connection

point at which you wish to oper-ate the

product meets the specified requirements.

Damaged electrical connection cable

The insulation on electrical connection cables

is often damaged.

This may have the following causes:

• Passage points, where connection cables

are passed through windows or doors.

• Kinks where the connection cable has

been improperly fastened or routed.

• Places where the connection cables have

been cut due to being driven over.

• Insulation damage due to being ripped

out of the wall outlet.

• Cracks due to the insulation ageing. Such

damaged electrical connection cables

must not be used and are life-threatening

due to the insulation damage.

Check the electrical connection cables

for damage regularly. Make sure that the

connection cable does not hang on the

power network during the inspection.

Electrical connection cables must comply

with the applicable VDE and DIN provisions.

Only use connection cables with the marking

"H05VV-F".

The printing of the type designation on the

connection cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must

have a cross-section of 1.5 mm².

Connections and repairs of electrical

equipment may only be carried out by an

electrician.

Please provide the following information

in the event of any enquiries:

Storage/Electrical connection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PZKS 1500 B2 - IAN 295934 Seite 107

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info