Bedienungsanleitung Parrot Bebop 2 (Seite 24 von 25) (Deutsch)

637598

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

46 47

MY GOPRO WON’T POWER ON

Make sure the camera’s battery is charged or the array is connected to an

external power supply.

OMNI UNEXPECTEDLY POWERS OFF

Omni might unexpectedly power off for a number of reasons:

• Insufficient power to the array from an external power supply

• Insufficient power to the array from the camera batteries

• Insufficient, incorrect, or excessive voltage/amperage from an external

power supply

• Missing camera from the array

• Camera without array camera firmware

• Fully depleted or nearly depleted camera battery

• Full microSD cards (no action was taken when SD CARD FULL message

appeared on a camera)

CAMERAS IN OMNI WON’T RECORD

Check the cameras for errors:

• If the primary camera has a problem, the camera status screen

displays a message describing the problem. For more information,

see Important Messages (page 44).

• If one of the secondary cameras has a problem, the primary camera

displays Array Error and the camera status light on the primary camera

flashes rapidly. For more information, see Array Error (page 44).

MY OMNI ISN’T BEHAVING AS EXPECTED

This issue is often caused by switching from one power source to another

when the camera is powered on. To switch from camera batteries to

external power (or external power to batteries), you must first power off

the camera.

Omni takes a moment to recognize the external voltage being supplied.

• Without camera batteries installed, Omni might not respond to a

rapid attempt to power up, if the external power supply was not

yet recognized.

• With camera batteries, a rapid power up might lead to the camera

batteries initially powering up the Omni and then switching over to the

external power.

To prevent these situations, wait a moment after connecting the external

power before powering up Omni.

Note: When camera batteries are installed, check the camera status lights to determine

if the external power is recognized. Unless the camera batteries are fully charged, the

status lights illuminate after the external power is recognized.

MY GOPRO WON’T RESPOND WHEN I PRESS A BUTTON

Press and hold the

Power/Mode button [

] for 8 seconds to reset your

camera. This reset saves all of your content and settings, and powers off

your camera.

I WANT TO RESET MY GOPRO SETTINGS TO THE DEFAULTS

In Setup mode, select Camera Reset, and then select Reset Defaults.

This option does not reset the Date/Time.

I POWERED OFF MY GOPRO, BUT THE BLUE LIGHT IS

STILL BLINKING

The blue light indicates that Wireless is on. To turn off Wireless, go to

Setup mode. Press the Shutter/Select button [

] to select Wirleless,

then press it again to turn Wireless off.

For more answers to commonly asked questions, see

gopro.com/help.

TROUBLESHOOTING TROUBLESHOOTING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parrot Bebop 2 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parrot Bebop 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info