Bedienungsanleitung Partner P4-20XT (Seite 13 von 15) (Deutsch, Englisch, Französisch, Spanisch)

518735

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

BAR MAINTENANCE

If your saw cuts to one side, has to be forced

through the cut, or been run with an improper

amount of bar lubrication it may be necessary

to service your bar .

A worn bar will damage your chain and make

cutti ng difficult.

After each use, ensure ON/STOP switch is in

the STOP position, then clean all sawdust from

the guide bar and sprocket hole.

To maintain guide bar:

S Move ON/STOP switch to the STOP posi-

tion.

S Loosen and remove chain brake nuts and

chain brake. Remove bar and chain from

saw.

S Clean the oil holes and bar groove after each

5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process

of rail wear. Remove these burrs with a flat

file.

S When rail top is uneven, use a flat file to re-

store square edges and sides.

Correct Groove

Worn Groove

File Rail Edges

and Sides

Square

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when exce-

ss heating or burring of the rails occurs. If re-

placement is necessary, use only the guide bar

specified for your saw in the repair parts list or

on the decal located on the chain saw .

SPARK PLUG

The spark plug should be replaced each year

to ensure the engine starts easier and runs bet-

ter . Ignition timing is fixed and nonadjustable.

1. Loosen 3 screws on cylinder cover.

2. Remove the cylinder cover .

3. Pull off the spark plug boot.

4. Remove spark plug from cylinder and dis-

card .

5. Replace with Champion RCJ--7Y spark

plug and tighten securely with a 19 mm

socket wrench. Spark plug gap should be

0,5 mm.

6. Reinstall the spark plug boot.

7. Reinstall the cylinder cover and 3 screws.

Tighten securely.

Screws

Spark

Plug Boot

Spark

Plug

Cylinder

Cover

CHA I N SHA R PE N ING

Chain sharpening is a complicated task that

requires special tools. We recommend that you

refer chain sharpening to a professional chain

sharpener .

CAR B UR E TOR ADJ UST M E NTS

WARNING: Thechainwillbemoving

during most of this procedure. Wear your pro-

tective equipment and observe all safety pre-

cautions. The chain must not move at idle

speed.

The carburetor has been carefully set at the

factory . Adjustmen ts may be ne cessary if you

notice any of the following conditions:

S Chain moves at idle. See IDLE SPEED--T

adjusting procedure.

S Saw will not idle. See IDLE SPEED--T ad-

justing procedure.

Idle Speed ---T

Allow engine to idle. If the chain moves, idle is

too fast. If the engine stalls, idle is too slow. Ad-

just speed until engine runs without chain

movement (idle too fast) or stalling (idle too

slow). The idle speed screw is located in the

area above the primer bulb and is labeled T.

S Turn idle speed screw (T) clockwise to in-

crease engine speed.

S Turn idle speed screw (T) counterclockwise

to decrease engine speed.

STOR A GE

WARNING:Stop engine and allow to

cool, and secure the unit before storing or

transporting in a vehicle. Store unit and fuel

in an area where fuel vapors cannot reach

sparks or open flames from water heaters,

electric motors or switches, furnaces, etc.

Store unitwithall guards inplace. Positionso

that any sharp object cannot accidentally

cause injury to passersby. Store the unit out

of reach of children.

S Before storing, drain all fuel from the unit.

Start engine and allow to run until it stops.

S Clean the unit before storing. Pay particular

attention to the air intake area, keeping it free

of debris. Use a mild detergent and sponge

to clean the plastic surfaces.

S Do not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an

open flame from hot water heaters, electric

motors or switches, furnaces, etc.

S Store in a dry area out of the reach of chil-

dren.

S Ensure the machine is cleaned and that a

complete service is carried out before long--

term storage.

S The guide bar and chain must always be

covered with a scabbard when the machine

is being transported or in storage in order to

prevent accident contact with the sharp

chain. Even a non--moving chain can cause

serious cuts to yourself or persons you

bump into with an exposed chain.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Partner P4-20XT Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info