Bedienungsanleitung Pelgrim gwa 810 (Seite 20 von 23) (Deutsch, Englisch, Holländisch, Französisch)

133008

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

3736

3.1 General

The connection of this appliance to the electric mains must be done by an authorised

installer who is knowledgeable of the safety precautions and will carry them out. The

appliance is in compliance with European guidelines.

Important to know:

• The distance between the lowest point of the exhaust hood and the gas cooker should

be at least 70 cm. When using an electrical cooker this distance should be at least

50 cm.

• The mains voltage indicated on the dataplate on the appliance should be identical to

the mains voltage of the house installation.

• No other appliance must be connected to the duct (such as a hot water heater or a

heater) when the exhaust hood is connected to an existing exhaust duct.

• Please follow the local guidelines with regard to the ventilation of gas appliances.

• The exhaust will operate best when the exhaust pipe is as short and as straight as

possible.

• Check before starting drilling whether there is/are no installation pipe(s) present.

• The connection pipe to the exhaust hood has a diameter of 125 mm or 150 mm.

We recommend that the the exhaust pipe has the same diameter.

• The enclosed installation materials are suitable for reinforced concrete and brick walls.

Special plugs and screws may be required for other materials.

3 Installation

• The main current must be switched off during reparation or cleaning. Remove the

plug from the mains current or turn the switch in the meter cupboard to zero.

• Grease and oil are ﬂammable when they are overheated. Stay in the vicinity of the

cooker when preparing food.

This appliance is marked in accordance with European guideline regarding the

disposal of electrical and electronic appliances (AEEA). This product should be disposed

of in accordance with the local environmental regulations for disposal of waste. For

further information regarding the treatment, recovery and recycling of this product

you can contact your local council, the household waste service or the shop where you

purchased the product.

2.2 Exhaust circuit

Depending on the model there are three possible ways to connect this exhaust hood:

1. As exhaust hood on an exhaust duct. The cooking moisture

that is sucked in and ﬁltered is transported upwards (B1)or,

depending on your choice, to the back (B2) and then to the

outside. This is the best method!

2. As a re-circulation exhaust hood (excluding motorless exhaust

hoods). The grease and odour will be ﬁltered out of the

cooking moisture that is sucked in. The air that is sucked in

is not transported away but blown back into the kitchen (B1).

You will need to ﬁt a carbon ﬁlter.

Attention! The carbon ﬁlter needs to be ordered separately.

3. As a motorless exhaust hood. This model is only suitable

for installation in combination with a mechanical ventilation

circuit.

2 Safety

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pelgrim gwa 810 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info