Bedienungsanleitung Perel FT30C-FR (Seite 5 von 42) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

720265

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

FT10C/FR - FT15C/FR - FT30C/FR

V. 03 – 11/09/2017 5 ©Velleman nv

Connection

1. Connect the gas hose to the heater without forcing.

2. Install the pressure regulator on the gas cylinder.

3. Check if the connection of the pressure regulator is correctly sealed according to the used gas cylinder.

4. Open the valve of the gas cylinder or the pressure regulator if the gas cylinder does not feature a valve.

5. Check if the connection are correctly sealed using soapy water: soap bubbles may point to a gas leak.

Never test for gas leaks with an open flame.

The connections may have a left-handed screw thread. Consequently, they are threaded in a anticlockwise

direction.

Check if there is a clamp between the pressure regulator and the gas cylinder.

It is allowed to interconnect multiple gas cylinders to increase the fuel autonomy.

The feeding pressure is obtained through the pressure regulator and corresponds to the data on the

specifications table.

Only use certified replacement gas hoses.

It is recommended to use gas cylinders of 30 kg providing a thermal power of 30 kW. You are allowed

to use larger gas cylinders if more thermal power is needed.

It is recommended to use gas cylinders with an appropriate capacity to avoid problems due to partial

fuel gasification. The correct pressure (refer to the specification tag on the heater) is indicated by the

included pressure regulator or a similar model.

Make sure the feeding gas hose is in perfect condition. Only use flexible and appropriate models when

replacing the gas hose. Always respect the local regulations. Do not crimp the flexible hose.

6. Connection to the Mains

Before connecting the heater to the mains, check if the used power supply and frequency match the

specifications on the specification tag. Always respect the local regulations when connecting the heater to the

mains.

Only connect the device to an earthed mains.

Disconnect the device from the mains prior to any maintenance or cleaning activity.

Always make sure that the mains is earthed.

7. Switching On the Heater

1. Open the gas valve.

2. Flick the switch to position I.

3. Fully press and hold the gas valve. Operate the igniter several times.

4. The flame burns. Hold the gas valve pressed for 15 seconds to activate the safety mechanism.

5. Release the gas valve. The flame will keep burning.

The safety mechanism will automatically switch off the heater in a few seconds in case of an electric power

failure. This mechanism will also switch off the heater in case of a gas shortage. In both cases, follow the

explanation above to switch on the heater again.

6. Regulate the gas flow.

7. Avoid operating the igniter for a prolonged period. Check for problems if the heater does not switch on.

8. Checking a Switched-On Heater

Check a switched-on heater by observing the pilot flame at the air exit of the heater. Make sure that the pilot

light burns steadily inside the burner.

Be careful when checking the pilot light as the air exiting the heater can be extremely hot. Maintain

yourself at a safe distance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Perel FT30C-FR Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info