Bedienungsanleitung Petsafe PWW00-14898 (Seite 6 von 7) (Englisch)

770997

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

1110

4) Once the filter is rinsed off, place inside the filter housing case with

the larger side facing down. The filter will only fit inside the case one

way, if it does not fit, flip it over. Attach the lid to the filter housing

case, press down until you hear it snap in place.

5) Attach the filter housing case to the pump by inserting the raised notch

inside the circular opening on top of the pump (Fig. 18). The opening

on top of the filter case should be right next to the raised post.

Fountain Reassembly

Fig. 17

2) Once the extra slack is

removed from the cord, affix

the rubber cap over the post to

seal off the bowl.

3) Rinse a new charcoal filter

thoroughly in cold water to help

remove any excess and loose

charcoal dust.

Fig. 19

Fig. 18

6) Reinsert the rubber grommet into the circular opening at the top of the

tower. Place it inside the hole and then gently work the piece into the

hole so that the top edge rests flat inside the dish. This will create a

seal between the filter housing case and the tower (Fig. 19).

7) Align the tower with the

rectangular indentation inside

the bowl and carefully lower it

until it rests flat (Fig. 20).

Fig. 20 a) Clean the pump more frequently

b) Clean with regular white vinegar

and let the vinegar soak for

several minutes down inside the

pump’s cavity

c) Use bottled water

Living in a humid environment, you may experience problems with mold or

algae, making the fountain feel slimy. Simply soak all of the plastic parts

(excluding the pump) in a diluted bleach solution for about ten minutes after

regular cleaning. We recommend using a mixture of 10% bleach and 90%

water. Pour some of the bleach solution inside the pump’s cavity as well

for additional disinfecting. Be sure to rinse all the parts very thoroughly

to remove all the chlorine. The best way to rinse out the pump’s cavity is

to hold it under a weak stream of water. Cleaning the fountain parts with a

bleach solution is also a great way to disinfect.

If hard water is an issue where you live, you may see white mineral

deposits inside the housing and inside the pump. These mineral deposits

may eventually prevent the impeller from turning properly. To avoid having

to replace the pump:

8) Place the fountain in a desired location. If placing on carpet,

tile or wood flooring, use a protective mat or other durable,

water resistant surface. This will help protect your floor from any

splashing or spills caused by your pet.

9) Fill the fountain by pouring water directly into the bowl. Leave at

least a half inch (1.27 cm) of space between the water level and the

rim of the bowl to help control spills and splashing.

10) Make sure the cord, the adaptor and your hands are completely dry

before you plug the fountain in. Connect the inline plug and make sure

no silver is showing, then plug the adaptor into an electrical outlet.

The Fountain and

Your Environment

Fountain Reassembly

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PWW00-14898 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info