Bedienungsanleitung Philips 14PV220 (Seite 26 von 28) (Englisch)

33125

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

If you encounter problems with your TV-Video Combi, these

could be caused by one of the following. You can also call the

customer service centre in your country.

The telephone number is listed in the enclosed warranty

information packet or on the last page of the manual cover.

Have the model number (MODEL NO) and the production

number (PROD.NO) of your video recorder ready. You can find

both numbers printed on the type plate fixed at the rear of the

set.

Your TV-Video Combi does not respond to any button being

pressed:

• TV-Video Combi has been switched off using the power switch

8 : switch machine on on left side using the power switch.

• There is no power supply: Check the power supply.

• A programmed recording is currently being made: If desired,

cancel the programmed recording pressing the

STANDBY m

button (for longer than 3 seconds).

• Parental control is on: Switch the parental control off.

Remote control does not work

The red standby lamp (STANDBY 5) does not blink, if one of the

buttons on the remote control is pressed:

• Remote control not pointed toward the TV-Video Combi: Point the

remote control at the TV-Video Combi.

• There is a technical problem: Take out the batteries, wait for 10

seconds and place them back.

• Batteries are weak: Change the batteries.

Technical problem:

• Switch machine off using power switch 8 , wait 30 seconds

and switch back on.

• You can reset the settings on your set (careful: all information will

be deleted):

1. Switch machine off using power switch

8 .

2. Press the

m button on the machine and hold button. Switch

back on using power switch

8 .

3. If the standby lamp (

STANDBY 5) on the set begins to blink,

release the

m button.

The machine settings are reset and the data memory is deleted.

No picture (black/blue picture):

• The red standby lamp (STANDBY 5) on the front of the set is not

lit up:

TV-Video Combi switched off: Switch on the set using the mains

switch on the left side of the unit.

There is no power supply: Check the power supply.

• The red standby lamp (

STANDBY 5) on the front of the set is lit:

TV-Video Combi switched off automatically: Switch it back on

using the

;P q button.

Switched to the programme number of an external source, e.g.:

’

E1’ for the scart socket EXT , but the attached device is

turned off: Switch on external device or choose a different

programme number.

A TV channel (programme number) has been chosen but there is

no reception on this channel: Select the correct TV channel.

No reception: Have the aerial checked.

Some of the menu lines can be selected, but are without

functions:

• Recording is in session; if required, cancel recording session.

• Hotel mode switched on; if necessary, switch off hotel mode.

No sound, volume cannot be increased:

• Hotel mode was activated with volume too low:

1. Switch off hotel mode.

2. Set the new max. volume level for hotel mode.

3. Switch on hotel mode.

Detailed information is available in the section ’hotel mode’.

Cassette is jammed in the TV-VIDEO Combi:

• Don’t use force. Switch off with the 8 power switch for 30

seconds, then switch it on again.

No playback on the TV-Video Combi:

• There is no recording on the cassette: Change the cassette.

Poor quality playback on the TV-Video Combi:

• The cassette is badly worn or of poor quality: Use a new

cassette.

• Tracking is not properly adjusted: Turn to chapter ’PLAYBACK

FUNCTIONS’ and read the section ’Eliminating picture

interference’.

Poor playback of recordings made via the scart socket

EXT :

• Recording copy-guarded data via the scart socket EXT can

lead to picture/sound distortions. This is not a fault in your

machine.

The TV-Video Combi will not record:

• The TV channel is not stored or not selected properly: Check TV

channels stored.

• You have loaded a cassette which is erase protected: Undo the

erase protection on the cassette.

Programmed recording does not work:

• You have not set the TIMER properly: Check the TIMER blocks.

• Clock/date were set incorrectly: Check clock/date.

• You have put in a cassette that is erase protected: Undo the

erase protection on the cassette.

• ’VPS/PDC’ switched on but ’VPS/PDCtime’ wrong: ’Enter

’VPS/PDCtime exactly to the minute. Have the aerial checked.

• The machine has not been switched to standby when recording

starts: Switch machine off in time before recording using the

STANDBY m button.

• After a ’programmed recording with Video Plus+’ the programme

number of the TIMER block does not correspond with the desired

programme number:

1. Confirm the PlusCode programming number using the

button.

2. Press the

TIMER k button.

3. Change the programme number displayed in the ’

PROG.’

entry field.

4. Confirm with the

TIMER k button.

9. BEFORE YOU CALL AN ENGINEER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 14PV220 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 14PV220

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info