Bedienungsanleitung Phoenix Gold Elite (Seite 4 von 7) (Englisch)

492013

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Elite Amplier Owner’s Manual

INPUT

Connect preamp signal cables from the head unit to these terminals.

200mV to 8v is the input voltage range.

FAN

The internal fan is nearly inaudible but the end user can control the fan’s

mode via the endpanel switch.

ON:

Fan runs at full speed at all times regardless of the heatsink

temperature. This is recommended for heavy users or low impedance

loads such as 1 ohm stereo/2 ohms bridged.

OFF:

Internal fan is o. This is only recommended for short periods of

time. For example, a sound quality competition.

AUTO:

Best setting for most users. Internal fan is o until the heatsink

temperature reaches 50°C/120°F then the variable fan turns on and its

speed is controlled by the heatsink temperature.

REMOTE LEVEL CONTROL

This port is for connecting the subwoofer remote level control. This is not a bass

boost, it controls the level of the low pass signal

only. Cong switch must be set to

“LP/BP” for the remote to operate.

HP AND LP CROSSOVER FREQUENCY

Controls the crossover point for the speaker outputs. See page 8 for exact crossover

settings.

LEVEL

Used to reach maximum amplier power with a wide variety of headunits.

CONFIG

FLAT:

Crossovers are turned o

HP:

High pass crossover is on

LP/BP:

Low and High Pass crossovers are on, creating a Bandpass (BP) setting for

midbass drivers or subwoofers. For a standard subwoofer system, the high pass

frequency now becomes a subsonic lter. To turn subsonic lter o, turn the HP

FREQ (Subsonic Filter) to 20Hz.

+12V

This must be connected to the fused positive terminal (+12V) of the car’s

battery. The fuse must be located within 18 inches of the battery.

REMOTE

This must be connected to switched +12V, usually a trigger wire coming

from the head unit or ignition.

GROUND

This must be connected to the negative terminal of the car’s battery or

bolted to a clean, unpainted part of the chassis of the vehicle.

RMD

Optional RMD Voltage Display plugs into this port. Sold separately.

CLIP INDICATOR

Lights when the amplier reaches near maximum output. Under normal

operation the clip indicator should be ashing during the peaks of the

music. The clip indicator should not stay lit for long periods of time (more

than 2 or 3 seconds), if this is the case you need to reduce system volume

or level of the amplier.

PROTECT INDICATOR

Lights red if there is a problem with the audio system. For example, speaker

wire is pinched/shorted, the amplier is running too low of an impedance

or reached an unsafe temperature.

SPEAKER OUTPUTS

Used to connect the amplier to speakers. Minimum impedance is 2 ohms

bridged or 1 ohm stereo. Minimum speaker wire size is 16 gauge. Use Left

+ and Right - to bridge the channels.

ELITE.2 FUNCTIONS

INPUT

Connect preamp signal cables from the head unit to these terminals.

LP CROSSOVER FREQUENCY

Controls the lowpass crossover point for the speaker outputs. See page 8 for

exact crossover settings.

BASS BOOST

Variable bass boost from 0 to +18dB @ 45Hz.

REMOTE LEVEL CONTROL

This port is for connecting the subwoofer remote level control. This is not

a bass boost, it controls the level of the low pass signal. This control is not

compatible with the Phoenix Gold LPL or RBC level controls.

OUTPUT MASTER/INPUT SLAVE

See page 11 for details how to link two Elite.1s together.

IMPORTANT: FOR

NORMAL USE, MAKE SURE THE SWITCH IS SET TO OUTPUT MASTER.

If its set

to INPUT SLAVE during normal use the amplier will have no output.

LEVEL

Used to reach maximum amplier power with a wide variety of headunits.

SUBSONIC CROSSOVER FREQUENCY

Controls the highpass crossover point for the speaker outputs to eliminate

extreme low frequencies.

CLIP INDICATOR

Lights when the amplier reaches near maximum output. Under normal

operation the clip indicator should be ashing during the peaks of the

music. The clip indicator should not stay lit for long periods of time (more

than 2 or 3 seconds), if this is the case you need to reduce system volume

or level of the amplier.

PROTECT INDICATOR

Lights red if there is a problem with the audio system. For example, a speaker

wire is pinched/shorted, the amplier is running too low of an impedance or

reached an unsafe temperature.

+12V

This must be connected to the fused positive terminal (+12V) of the car’s

battery. The fuse must be located within 18 inches of the battery.

REMOTE

This must be connected to switched +12V, usually a trigger wire coming

from the head unit or ignition.

GROUND

This must be connected to the negative terminal of the car’s battery or

bolted to a clean, unpainted part of the chassis of the vehicle.

SPEAKER OUTPUTS

Used to connect the amplier to subwoofers. Minimum impedance is 1

ohm. Minimum speaker wire size is 12 gauge.

RMD

Optional RMD Voltage Display plugs into this port. Sold separately.

PHASE

This allows the phase of the amplier output to be adjusted from 0 to 180

degrees. This adjustment can help achieve better “up front” subwoofer

bass and resolve subwoofer cancellation problems in certain installations.

Each installation is dierent, slowly adjust and listen for best results.

ELITE.1 FUNCTIONS

Phoenix Gold Elite Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info