643479
64
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
Problem Cause Solution
a Some of the problems indicated below may be resolved by following the instructions. All work must be carried out when the appliance
is cold and disconnected from the electricity supply (pull out the plug).
a Authorised qualied persons must be contacted, in accordance with current regulations, whenever it is necessary to work on parts
inside the cladding or the rebox in order to resolve the problem.
It is therefore recommended that only your authorised service dealer be contacted.
Installation and repair sholud only be performed by a qualied service technician. Do not attempt to service the appliance yourself.
a Unauthorised tampering with the appliance or the use of other than original spare parts not only creates situations of risk for operator
safety, but invalidates the warranty and relieves the manufacturer from all liability.
8.0 TROUBLESHOOTING
The control panel display is not lit The appliance is not powered
Check that the power cable is plugged
into the wall socket and connected to
the appliance
Faulty power cable
Replace the power cable (use only
original spares)
Fuses blown
Check the fuses in both the plug and
the electronic board, replacing them if
necessary. If the problem persists call
an electrician
Faulty control panel
Replace the control panel (use only
original spares)
Faulty at cable
Replace the at cable (use only
original spares)
Faulty electronic board
Replace the electronic board (use only
original spares)
Stove combustion gas safety device
“ALF 1” stove status
Blocked ue or ue gas outlet
Check and clean the ue and the
outlet
Fuel hopper lid remained opened for
more than 60 s
Control if the lid is closed
Broken smoke extractor
Replace the motor (use only original
spares)
Fire door open Control if the door is closed
Flue system too long Check correct installation
Damaged door sealing gaskets
Check all the gaskets and seals of the
door and ue pipe
Hose connection blocked
Dismantle and clean the hose
connection for the vacuum gauge
Silicone piping blocked or broken Check and/or replace piping
Faulty electronic board
Replace the electronic board (use only
original spares)
H07031310 / DT2002112 – 00
64
English
DT2011179-01
64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

piazzetta-p958-c

Suche zurücksetzen

  • wie kann ich das abgasgebläese aus und einbauen danke Eingereicht am 22-5-2019 13:11

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Piazzetta P958 C wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info