Bedienungsanleitung Pioneer anh-p10mp (Seite 7 von 170) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

162112

Zoom out

Zoom in

Vorherige Seite

1/170

Nächste Seite

Connecting the Units

English

Español

Deutsch

Français

Italiano

Nederlands

<CRD3863-A> 7

• Do not earth more than one product

together with the earth from another

product. For example, you must sepa-

rately earth any amplifier unit away

from the earth of this unit.

Connecting earths together can

cause a fire and/or damage the prod-

ucts if their earths became detached.

Notes

• This unit is for vehicles with a 12-volt battery

and negative earthing. Check the battery volt-

age of your vehicle before installation.

• To avoid shorts in the electrical system, be

sure to disconnect the ≠ battery cable before

beginning installation.

• Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

• To protect the wiring, wrap adhesive tape

around them where they lie against metal

parts.

• When replacing the fuse, be sure to use only a

fuse of the rating prescribed on the fuse

holder.

• Since a unique BPTL circuit is employed, do

not directly earth the ≠ side of the speaker

lead or connect the ≠ sides of the speaker

leads together. Be sure to connect the ≠ side

of the speaker lead to the ≠ side of the

speaker lead on this unit.

• If the RCA pin jack on the unit will not be

used, do not remove the caps attached to the

end of the connector.

• Never connect speakers with an output rating

of less than 50 W channel or impedance out-

side of the 4 ohms to 8 ohms specifications to

your Navigation system. Connecting speakers

with output and/or impedance values other

than those noted here may result in the speak-

ers catching fire, emitting smoke, or becom-

ing damaged.

• When this product is switched ON, a control

signal is output through the blue/white lead.

Connect to an external power amp’s system

remote control (max. 300 mA 12 V DC). If the

vehicle features a glass aerial, connect to the

aerial booster power supply terminal.

• When an external power amp is being used

with this system, be sure not to connect the

blue/white lead to the amp’s power terminal.

Likewise, do not connect the blue/white lead

to the power terminal of the auto aerial. Such

connection could cause excessive current

drain and malfunction as well as damage to

the auto aerial of the vehicle.

• To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused speaker

leads, which if left uncovered may cause a

short circuit.

• To prevent incorrect connection, the input

side of the IP-BUS connector is blue, and the

output side is black. Connect the connectors

of the same colours correctly.

• When the auto aerial function is used by con-

necting the blue/white lead to the vehicle with

the auto aerial function, either turning off the

ignition switch or detaching the front panel

will retract the auto aerial of the vehicle.

CRD3863A_inst_002-029_UK 4/9/04 2:05 PM Page 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer anh-p10mp Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer anh-p10mp

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info